Jump to content
SAU Community

The Greatest Engine of All Time

hadean

By hadean,
in General Automotive Discussion

 Share

Recommended Posts

Lithium Grand Master

Lithium

Posted
Posted

I go with the F20C as well - that article is done from a euro point of view as well, the Japanese spec one is around 250ps... ie, the same as an RB25DET :)

They are reliable, sound awesome, light, economical, are smooth, have low emissions, make awesome power for an NA motor (hey, they are higher than a lot of equivalent displacement turbo motors), and are really tractible etc. And they aren't on the razors edge to make that power, do an intake, exhaust, ECU and tuning etc and there is still more to be had. One of my mates was making over 150rwkw on his mildly modded S2000s, which makes for some fun driving :(

There may be some limited run NA motor that matches its peak power/l - but I doubt that motor can match the F20C in the other aspects... it might also be peaky as a mofo and not actually end up being as good an overall performer. The F20C is a jack of all trades in its displacement range.

Abo Bob Grand Master

Abo Bob

Posted
Posted

So if you drive it like a pansy you can get 13.6L/100km and some of you are saying thats economical???

And isn't there a torque difference between an RB25 and an F20C?

As for Chryslers, how is a 225 slant better than a 265 hemi? I've been in a Charger with 265 that could spin the wheels with ease in 3rd and 4th gears at speeds well over 100km/h. Admittedly it idled like a plate of jelly.

JCMarshall_Law Proficient

JCMarshall_Law

Posted
Posted

Considering standard production engines, Honda make some great ones, F3 and F4 CBR 600 (motorbike) engines, F3 is prolly a better engine but the F4 is fuel injected. The sequential gearboxed on these engines are great.

How can you look past the Ford Windsor V8, designed back in the 1950's, the same basic design is still used in both ford production cars and V8 Supercars.

Brackez Contributor

Brackez

Posted
Posted

Turbo 6: RB26DETT (Of course. Closely followed by 2JZ-GTE)

N/A 6: Hard pick, 265 Hemi (1/4 mile champ for all Aussie made cars till 96-V8s included) over 186 red motor (need some work to make em go, but they rev like mad for an old pushrod heap).

V8: 350 Chev- widely regarded as the best bang for buck drag engine available.

Turbo 4: FJ20DET.

N/A 4: the 1400 in my sister's old rwd 323. It took a thrashing ;) , never missed a beat, and was amazingly simple to work on. SOHC & crossflow head not bad for 78.

dojobi Experienced

dojobi

Posted
Posted

I wouldn't go past the new BMW 4.8L 2nd gen valvetronic engine. There really is no better car engine in the world. With infinitely variable valve timing AND lift + 4.8L of capacity, what could be better?

If I were to choose a 6, it'd be the VVTi 2JZ-GTE.

relicr31act Collaborator

relicr31act

Posted
Posted

If the argument is (and I'm not saying that it is) that the greatest engine is the "winningest" (nice word huh?) engine, then the Chevrolet small block V8 would be first with daylight second. This engine has won in everything from jet boats to speedway and everything else besides. Admittedly there ain't a whole lot of Chevrolet bits spinning around inside them but they were originally a Chevy small block designed by one of the greatest engineers, Mr Duntov.

martinwollaston Apprentice

martinwollaston

Posted
Posted

[And it's fuel efficient in that one can - 'one' I assume being someone limper of wrist - drive to an average of 13.6L/100km (32mpg). Hell, it even looks good, longitudinally mounted as an engine should be.

When is 13.6L/100km 32 mpg? I thing that around 9.6L is 32mpg. What do you think?

PTR33 Proficient

PTR33

Posted
Posted
[And it's fuel efficient in that one can - 'one' I assume being someone limper of wrist - drive to an average of 13.6L/100km (32mpg). Hell, it even looks good, longitudinally mounted as an engine should be.

When is 13.6L/100km 32 mpg?  I thing that around 9.6L is 32mpg.  What do you think?

13.6 is 19.8 mpg.

Sounds like the pom failed maths

Col-GTSX Grand Master

Col-GTSX

Posted
Posted

Well the greatest engine of all time has to be.......................

Drum roll

>>>>>>>>>>>>>> Scram Jet Engine <<<<<<<<<<<<<

Well im fitting my scram jet engine next week. Should be able to do 0-100 in a half a second and 100-1000 is .23 of a second, but yeah there is some fearce competition out there with the GTR's so im not overlly confident.... LOL

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • wizlb
      Who has a Infiniti Q60, Q50 (V37)?

      By wizlb · Posted

      I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Kinkstaah
      Starting again

      By Kinkstaah · Posted

      Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...