Jump to content
SAU Community

Recommended Posts

heya,

being a n00b to imports i have to ask this rahter simple question....

my r33 is up for its 5000km oil and filter change and i am wondering what is the best oil to use? it currently uses motul. i have heard heaps of ppl using motul oil and praising it so i was planning on using it again. but i dont know which type/code of motul oil is best to use? can some one please help me out with this, cause the last thing i want to be doin is putting some crapy oil in my motor.

if anyone has any other brands/types of oil they reccomend using please feel free to post away.

cheers!

matty. ;)

Link to comment
https://www.sau.com.au/forums/topic/64031-which-oil-rb25/
Share on other sites

my car's running Penzoil 10w40, runs alright. (i think it's called GT performance or some sh1t)

If you don't wanna spend $60 on mobile1, it's a good alternative, for around $35 (from repco).

If the car starts to burn oil, try for a higher hot weight oil (eg 10w50). Choose a cold weight between 5-15 and you should be fine, don't go higher than 15 for turbos.

Link to comment
https://www.sau.com.au/forums/topic/64031-which-oil-rb25/#findComment-1202786
Share on other sites

Hey SK

On a new (18,000 Km RB30DET) engine. Currently using Genuine Nissan oil

Wich oil would you be using The 10-60 or the 0-40?

Daily Driver. Rarely reved over 4.5K. Sometimes a few blasts just for fun. Hoping to take it to the Drag strip in the future.

Link to comment
https://www.sau.com.au/forums/topic/64031-which-oil-rb25/#findComment-1202989
Share on other sites

I've always used Castrol 15/40 semi synthetic, no complaints from me ( or the motor ) after 3 years of using it (I change oil + oil filter every 6 months though).

Where i get my car dyno'd swears by Penrite HPR 40. Thats what he uses on everything! including his 7sec RX drag car.

so many people have so many opinions and preferences. It's really up to yourself and your price range. Generally anything in the lower numbers form 0-15 is fine, and in the higher about 30-40 area, in both semi-synthetic blend and full synthetic oils.

my 2 cents

;)

Just read the blurb on the back of the container......if it mentions its ok for performance/turbo charged cars....its ok

Link to comment
https://www.sau.com.au/forums/topic/64031-which-oil-rb25/#findComment-1205228
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • our good friends at nismo make a diff for it, I have one (and a spare housing to put the centre in) on the way. https://www.nismo.co.jp/products/web_catalogue/lsd/mechanical_lsd_v37.html AMS also make a helical one, but I prefer mechanical for track use in 2wd (I do run a quaife in the front, but not rear of the R32)
    • What are we supposed to be seeing in the photo of the steering angle sensor? The outer housing doesn't turn, right? All the action is on the inside. The real test here is whether or not your car has had the steering put back together by a butcher. When the steering is centred (and we're not caring about the wheel too much here, we're talking about the front wheels, parallel, facing front) then you should have an absolutely even number of turns from centre to left lock and centre to right lock. If there is any difference at all then perhaps the thing has been put back together wrongly, either the steering wheel put on one spline (or more!) off, and the alignment bodged to straighteb the wheel, or the opposite where something silly was done underneath and the wheel put back on crooked to compensate. Nut there isn't actually much evidence that you have such a problem anyway. It is something you can easily measure and test for to find out though. My money is still on the HICAS CU not driving the PS solenoid with the proper PWM signal required to lighten the load at lower speed. If it were me, I would be putting either a multimeter or oscilloscope onto the solenoid terminals and taking it for a drive, looking for the voltage to change. The PWM signal is 0v, 12V, 0V, 12v with ...obviously...modulated pulse width. You should see that as an average voltage somewhere between 0V and 12V, and it should vary with speed. An handheld oscilloscope would be the better tool for this, because they are definitely good enough but there's no telling if any cheap shit multimeter that people have lying around are good enough. You can also directly interfere with the solenoid. If you wire up a little voltage divider with variable resistor on it, and hook the PS solenoid direct to 12V through that, you can manually adjust the voltage to the solenoid and you should be able to make it go ligheter and heavier. If you cannot, then the problem is either the solenoid itself dead, or your description of the steering being "tight" (which I have just been assuming you mean "heavy") could be that you have a mechanical problem in the steering and there is heaps of resistance to movement.
    • Little update  I have shimmed the solenoid on the rack today following Keep it Reets video on YouTube. However my steering is still tight. I have this showing on Nisscan, my steering angle sensor was the closest to 0 degrees (I could get it to 0 degrees by small little tweaks, but the angle was way off centre? I can't figure this out for the life of me. I get no faults through Nisscan. 
    • The BES920 is like the Toyota Camrys of coffee machines. E61 group head is cool, however the time requirements for home use makes it less desirable. The Toyota Camry coffee machine runs twin boilers and also PID temp control, some say it produces coffees as good as an E61 group head machine.
    • And yes with a full tank it will hit limiter free revving or driving 6B6CDF6E-4094-426D-A9CB-6C553475FE36.mp4
×
×
  • Create New...