Jump to content
SAU Community

Recommended Posts

hi guys just a few questions 1 is do all gtie have quad throttle body's, 2  whats a stock gtir do on the strip and on the dyno, whats the best mods to do to them to make them go

A stock Gtir does around 14.2 sec on the quarter and the best mods for them are the same as any Jap Turbo ie FMIC, dump pipe, exhaust, pod filter, ebc set at 1.2 bar, fuel pump, power FC and coil overs should get you started.

The good thing about those cars are that the stock turbo (T28) isnt limited by the ceramic exhaust turbine that skylines are, so you can push them a fair bit harder.

From my understanding all Pulsar Gtirs have quad throttle bodies and solid lifters.

Link to comment
https://www.sau.com.au/forums/topic/64060-nissan-gtir/#findComment-1202825
Share on other sites

yes, as posted above all GTI-Rs have quad throttles and a nice steel wheel T28 which is good for up to (and sometimes just over) 180kw at all four.

A stock GTI-R will run anywhere from 14.3 down to 13.8 depending on the condition of the car, and who is driving it. on the dyno a stock GTI-R should make anywhere between 105kw atw up to 120kw atw again depending on conidtion and dyno.

best mod for your stock GTI-R is some good brake pads, good rotors and braided lines with some good fluid too. cause stock GTI-Rs are quick they just don't stop too well if the brakeing system isn't in peak condition. after that exhaust (dump, front and the rest), then some kind of high flow filter or pod with air box and cold air intake. wind up the boost to around 1 bar, and get a front mount if you want. you will now have anywhere between 140 and 165kw at all four and have a car that can do low somewhere between a high 12 and a low 13. NOTE: your clutch may now be on the way out, if so upgrade. now you'll need to make it handle properly so start with a bigger rear sway bar and replace every suspension bush you can think of with some urethane ones. now if you still have money start looking at coil-overs and most importantly get the suspension set up somewhere that knows what they are doing. now you have a very nice street car, but be aware that unless you are going to keep and enjoy it for a few years you will be dissapointed when you sell it. they are great little cars though.

Link to comment
https://www.sau.com.au/forums/topic/64060-nissan-gtir/#findComment-1202836
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • How dare you sell your unreliable Skyline and buy a reliable, Toyota/Yamaha car with a strong gearbox, torsen LSD and Toyota reliability. At least you won't need to worry about oil pumps, big catch can, oil restrictors, blowing off power steering belts, sheering off 3rd gear, failing ABS relays/pumps, etc.
    • Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • https://www.facebook.com/share/p/18rmVb1SKB/ 
    • The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
×
×
  • Create New...