Jump to content
SAU Community

Recommended Posts

Hey all,

well ive just had a 100,000km service done (change timing belt, radiator flush, full service and tune) i dont think this problem has been occuring long (certainly not before i got it done) but today i noticed that in first, after being in a stationary position, taking off sometimes it will semi pop or something.

By this i mean that usually when the foot comes off accel and u let it coast i can often get your standard sort of gurgle/popping.

Well in first when i take off sometimes, and have my foot on the accel, it will actually pop once or a couple of times, maybe its a misfire ?? I lose a lil power for an instant when it does it but yeah.

Dont think its clutch cus

1. just had it replaced

2. it doesnt feel like its slipping, and dont get any extra revs or anything that i can see/hear

Any help as to pointing out what this is ?

Link to comment
https://www.sau.com.au/forums/topic/64472-car-doing-wierd-things/
Share on other sites

My car pops and gurgles on most gear changes if i leave a gap in the change. ie if I change gear slowly

Not too sure if its just that your experiencing. If it is, im no mechanic but its probably nothing.

Possibly gap in your spark plugs are too big? I had that problem and car was running like shit on boost (but you shouldnt be having that problem :P )

I would think if it is occurring under acceleration then might be a coil pack on the way out. If they are goin to phuck up then it will be just after they have been move (plug change). Spray some CRC or simular on the areas around your coil packs that will stop them arcing on the head and that should stop the misfire.

or... take it back to where you got the service/work done and let them fix it. Thats if it was working fine before you went in. They probably would be able to tell you what it is straight away.. after all it is what they do for a living

Brett,

Timing belt off by one tooth - ouch - don't say that! I can hear poor daniels wallet opening WAY too wide :rofl:

I've never heard an N/A misfire like that before hey... on acceleration i mean :| But in a turbo it's usually coil packs or base timing well-retarded, or just plug gaps!

I would think if it is occurring under acceleration then might be a coil pack on the way out. If they are goin to phuck up then it will be just after they have been move (plugs change). Spray some CRC or simular on the areas around your coil packs that will stop them arcing on the head and that should stop the misfire.

Mirkz try this.....It works. :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...