Jump to content
SAU Community

Recommended Posts

Its not so much the power but the amount of Air that it can measure. For example a HKS GT-RS will make a certain power level at 14 psi and a standard turbo will make a bit less power. What I am trying to say is that I think the rb25 AFM will max out at about 14 psi. Now depending on what turbo you have your power levels at 14 psi could be anything from 180rwkw upwards.

If your rb25 has a stock turb then the stock AFM should see you to about 200 rwkw...

hope that makes sence :)

my airflow meter maxed out at 12psi and i was making just over 200kw

there are alot of things that you have to take into acount

you have to remember that hot wire air flow meters work by heating the little wire in side, when air passes over it, it changes the resistance in the wire so it takes more voltage to heat it and thats the signal that is send back to the ecu. once the voltage reaches 5.13 volts it cant heat the wire anymore and that is when you are maxed out

air density(temperature) plays a big part in this as colder air will cool the wire easyer

that i why mine maxed out at around 12psi and some of you guys can run up to 14 psi without a problem

i hope this has helped you

what symptoms would you have if your air flow meter was being "maxed out"

like if you didnt have an FC with commander telling you exactly whats going on. how could you tell?

Cheers

if your running a standard ecu it feels just like your boost cut and if you havnt hit that yet, it feels like your going to be thrown though your front windscreen, its a very sudden jolt. thats the best way i can explain it

I changed to rb20/25 afm's on my GTR becuase the std ones ran out of head room. I'm running 2530's at 1.2bar with rb25 afm's(same as rb20) and I more headroom then I need . Much cheaper option then z32's and the rb ones just plug straight in .

that's what he want's to hear :cheers:

to others he's talkin twin rb20/rb25 afm's on a gtr

This is from Sydneykid

Rule of thumb for Air Flow meters RWKW & Engine BHP

------ ---- OD ---- RWKW ---- RWKW ---- BHP ------ BHP

No of AFM's ---- ------- 1 -------- 2 -------- 1 -------- 2

RB26 ------ 65 ------ 149 ------ 299 ------ 271 ------ 474

RB20/25 --- 80 ------ 226 ------ 453 ------ 376 ------ 683

Z32 ------- 80 ------ 255 ------ 511 ------ 415 ------ 763

Q45 ------- 90 ------ 302 ------ 605 ------ 479 ------ 890

Your Engine warning light will also flash in a particular sequence when your AFM maxes out. This is often mistaken for knock... I am not sure what the 2 different sequences for knock and AFM Max out are though...

Is their a way of checking if the stock AFM is maxing out? without using an aftermarket ECU?
Is their a way of checking if the stock AFM is maxing out? without using an aftermarket ECU?

Sure can mate. if you have the car on the dyno the output voltage can be checked using a multimeter. anything over 5volts and the AFM is near max. infact with a pin out diagram you may be able to check what voltage the AFM is sending to the ecu (thus not needing to check it in the engine bay), this way you could check it on the street/strip instead of having to use a dyno.

  • 3 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...