Jump to content
SAU Community

Recommended Posts

Had my R33 GTS25t tuned at RUF performance today. I was reasonably happy with the result (185.5rwkw @ 12psi), although I was optimistically hoping for a little more to be honest. Power curve looks good all the way to the rev limit though.

Current mods are:

Power FC

Profec B Spec II EBC (12psi)

Blitz LM Intercooler

3" Cat Back Exhaust

K&N Panel Filter

Not sure what mods to do next - I wouldn't mind having 200+ rwkw :)

Link to comment
https://www.sau.com.au/forums/topic/65030-dyno-result-r33/
Share on other sites

definatley do dump/front pipe and hi flow cat, 10rwkw for sure + bit of money on side get exhaust cam gear that will see u over 200 for sure...

start preparing for a bigger afm and maybe even injectors, once youve got 200 it wont be long till u want more, and more heheh

ben...

Link to comment
https://www.sau.com.au/forums/topic/65030-dyno-result-r33/#findComment-1216968
Share on other sites

Thanks for the comments. I had replacing the front/dump pipe and getting a hi flow cat on my list of things to do...just didn't really have the dosh to do it right now (it was either that or get the ebc...I decided to get the ebc cause my bleed valve couldn't hold boost). I'm kinda hungry to get to 200rwkw though, so I might just put the credit card into more hurt town and get the exhaust work done in the next month or so. Can anyone recommend a good exhaust shop in Sydney? Also I've seen the split style dump pipes here. Are these the way to go?

Also, how much would an adjustable exhaust cam gear cost approximately?

My front/dump pipe dyno review here  

My Ex Cam Gear dyno review here

Theirs a solid 15-20rwkw for you :P

Edit: What happened from 6500-7000rpm?

Interesting results you got there - good to see there's a fair improvement with both sets of mods.

As for what happened between 6500-7000rpm, that's a bloody good question! I do know that the tuner set the rev limit to just over 7000rpm, but i've got no idea why the curve didn't print out for the last 500rpm.

Link to comment
https://www.sau.com.au/forums/topic/65030-dyno-result-r33/#findComment-1217148
Share on other sites

Also, how much would an adjustable exhaust cam gear cost approximately?
Approx $160 to purchase (nengun) and $100 to fit/tune.

Best bang for buck you'll get although your power curve is very nice so you may not notice as much as what I did.

Link to comment
https://www.sau.com.au/forums/topic/65030-dyno-result-r33/#findComment-1217157
Share on other sites

lovely curve you have there, all i can really suggest is a dump pipe for sure and i suppose why not get the exhaust cam gear as well becuase for the relatively low price, results such as what benm got from it are possible.

after that, make sure you pay off the credit card first becuase mods after that stage make the credit card go into hurt town a lot faster...haha...good luck with the quest for 200rwkw

Link to comment
https://www.sau.com.au/forums/topic/65030-dyno-result-r33/#findComment-1217541
Share on other sites

An adj cam gear (usually only put on the exhaust cam on RB25det engines) lets you fine tune the camshaft to the engine.

Most people have found that 3 to 4 degrees retarded on the exhaust cam works well, or is at least a good starting point.

Have a read through Benm's thread (link is above), it's a good write up.

J

Link to comment
https://www.sau.com.au/forums/topic/65030-dyno-result-r33/#findComment-1217683
Share on other sites

That graph looks VERY like mine when I run it for the first time with that dip in around the same spot, I didnt a a PFC though just a MINES chipped ECU other mods about the same though. That dip in power (on my car) was from it running rich(a slite miss) and all we could do at the time(because I had no tunable computer) was change plug gaps from .8 to .7 and it gave a perfect power curve and took the top power too 201kw with a huge gain in midrage. So id be looking at your air/fuel ratio in that 4000rpm range and that might just take you to your 200kw your chasing..... :cheers:

Link to comment
https://www.sau.com.au/forums/topic/65030-dyno-result-r33/#findComment-1218387
Share on other sites

Hey mason have you seen a yellow s5 rx-7 at ruff b4.He's a mate of mine.
Nah, didn't see it when I was there. There was a couple of nice looking Evo8's behind the workshop that caught my eye though...

Just had a look on the Greenline website and they've got a variety of adj cam gear's for around $160-$190 + freight. After seeing the results benm and Jay95R33 got with them, I think I'll invest in one of them once I've done the front/dump pipe...seems like a good bang for buck improvement.

muaythailuke, thanks for the advice. The tuner did say that he played around with a few things to try and smooth out the power curve in the mid-range. I'll mention the a/f ratios to him next time I'm down there...hopefully they might have the a/f graph still on file so I can take a look at it.

Link to comment
https://www.sau.com.au/forums/topic/65030-dyno-result-r33/#findComment-1219454
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I have been being VERY quiet about what you're alluding to, as it is something that ticks me off... The number of cars from factory that run coil overs is HUGE! Most of them these days do... The other part that annoys me, is people saying "Well all the incabin adjustable suspension is illegal by blah blah blah"... If that's the case, then why can I buy a car brand new that can do it if, FULL STOP in cabin adjustable suspension is illegal...   Also, I could just chuck some aftermarket shocks in my car, throw the stock springs on, after my blue slip, dump my super low springs back in. Same shock and spring style setup... Hell, they could also be the same colour springs etc.     I'm voting, BlueSlipper didn't want to touch the above car for some reason. Whether it be some sort of bias against the car, the owner, them maybe having previously done dodgy shit and now they're being super careful in case they get slapped in the face by the Gumbyment again... Find a new blueslip place.   And can confirm as you had said, yes there are holy bibles of vehicle heights, and all sorts of other suspension stuff. Heck your run of the mill mechanic, and tyre shop has access to all of that stuff. It's how they do wheel alignments...
    • Funny story Heading to Sydney this morning on the HWY there was some slow traffic, so I gave it the beans and midway through my overtaking "power run" I lost all power It seems that I missed a hose clamp,  and the MAF and filter went WiFi To make this more problematic, the little tool kit that lives in the boot, is sitting in the sun room at Goulburn......LOL Luckily for me I found a bit of steel on the side of the road that could be used like a rusty and bent flat head screw driver to tighten it up enough that it got me into Sydney, it is now all tight like a tiger with the aid of a 8mm socket Note to self: Use my brain and double check stuff, and always keep that little tool kit in the car for when I have a brain fart
    • Oh, and as for everyone with their fuel economy changes, I switch between E10 and 98 in the company car. Even do when I had personal cars that could run on E10. You know what changed my fuel economy in any noticeable way? How I drove, and where I drove. Otherwise, say on full tanks of just back and forth from work only (So same trips, same sort of traffic), couldn't notice a difference that I can correlate to the type of fuel in use. In the current vehicle, that's over 42L of USABLE fuel. While 98 is all "more energy dense", it also has higher knock resistance as it takes more energy to get it to ignite too. The longer hydrocarbons, typically more tightly bound. So running the same ignition map, can also produce less power, if there isn't enough time to get it all burnt through properly, as yep, the flame propagation speed is different from lower octane fuel to higher (Higher has a lower flame propagation, due to the more tightly bound and harder to self ignite funs. This is also typically where, a vehicle that is designed purely to run on 91 (Whether it be E10 or normal 91) usually sees absolutely no real world difference in fuel economy for the normal man, woman, or dog.
    • We've got some servos around me that have 91 with E10, 91 (no E10), 95, and 98. At those stations the change from 91 E10 to 91, is typically around 8c/L.   But lets not get started on the price of fuel in Oz. It's ridiculous. All the service stations around me, bar one, the price of fuel has been over the $2 mark per litre for the cheapest, 98 being around $2.45. That one service station is a CostCo, fuel from it comes from the same refineries, and makes no pitstops, it runs great, including the 98. In fact, I've had no issues on CostCo fuel, but plenty of issues at other stations!. The CostCo fuel, was $1.65 roughly this week for 94 with E10. $1.88 for 98. Servos directly across from it, $2.10 for 91 E10, and $2.48 for 98. The part I had to laugh at? If I drive multiple HOURS away from Brisbane, say out near Nanango, or Kingaroy, or even out to Goondiwindi, the price of their fuel, is the same as what it is at the CostCo... Oh, and that BP servo at Goondiwindi is HUGE and goes through epic turnover of fuel, so it's not sitting there for weeks going to shit. And what blows me away, my mate is one of the people who drives the Fuel Tanker all around QLD, delivering to all those places. At the same company his previous role was doing the "local haul" deliveries... Same truck, same driver, same pickup point it all comes from. So you tell me, how the hell it is 60c/L CHEAPER for fuel, when nearly all else is equal, except they require a B-Double to drive half a day out of Brisbane, and half a day back, every second day, compared to the delivery that can be under 30 minutes drive from the fuel pickup point... Not to mention, go five blocks down the road, and Ampol to Ampol will vary 30c/L... And I've had this conversation with my mate... The way it's priced, is just typical, pure and utter rubbish... He also does runs from Brisbane, to all over QLD, down to Newcastle, Sydney, Nowra, Melbourne, Geelong, and even out to parts of the NT depending on the companies needs. His main stuff is all the longer distance away from home for a few days at a time, then when he's back, he loves to just pickup extra shifts wherever he can in whichever truck, hence all the weird different places.   Oh, as for getting E10 into all the fuels in Australia... It was very quickly highlighted, that we don't have enough biomass available to use to make E10 sustainably like they require, and it would dramatically cut into our, and the worlds food chain supply...   I vote we all just start running on liquid methane gas... Plenty of that just getting tapped off at tips from underground decay... (Note, this is pure just stupid commenting. I could very easily highlight the reasons its not a good idea especially on scale...)
    • Am I correct in assuming that the R35's are getting the classic skyline haircut off the odometer?  Quick search on carsales, there are 33 08 and 09 GTR's for sale, only 2 of them have more then 100,000km's on them (116,075 and 110,000 respectively).  And somehow there are about 25 for sale with around 60,000kms? Looks like the classic skyline haircut to me =/
×
×
  • Create New...