Jump to content
SAU Community

Recommended Posts

Hey kids,

I was posting in another topic but I thought I'd start fresh.

My car (R32 RB20DET) idles realtively OK when its cold (about 1100rpm) but when the needle reaches the middle of the temp gauge, it idles at about 2000rpm - and about 1600rpm with the air-con on.

- The car idles LOWER with the air-con ON (i would've thought the idle control would adjust in the opposite direction to compensate for compressor?)

- It idles HIGHER as the car gets warmer

- I've read topics that say to clean the AAC and they talk about a spring and that it should function properly - I pulled mine apart and cleaned it with carby cleaner (which didn't fix the problem) - and NO spring was present. Can someone tell me where the spring is supposed to be?

Pics of my AAC below

HHHEEELLLPPP PPPLLLEEEAAASSSEEE

Cheers,

Jason

Link to comment
https://www.sau.com.au/forums/topic/65202-rb20-fast-idle/
Share on other sites

Is it missing or otherwise sounding lumpy?

Generally what happens if it detects irregular idling, it'll bump up the idle to compensate. Could be what's happening there. So could be nothing to do with the AAC..

Check the AFM as well.. give that a clean as well..

Link to comment
https://www.sau.com.au/forums/topic/65202-rb20-fast-idle/#findComment-1219558
Share on other sites

Check for vacuum leaks, mine idled really high when it had a few leaks. Worst culprit was a vacuum hose missing of the REAR fuel pressure reg. (R32's have 2) This is what was causing my high idle

Link to comment
https://www.sau.com.au/forums/topic/65202-rb20-fast-idle/#findComment-1220165
Share on other sites

My two suggestions:

1)  Your Air Flow meter is either f*cked, or,

2) You have a big aftermarket fuel pump without engine management

2) is exactly what I got! THANKS!

I've got an S-AFC2 to install - I guess that'll help me adjust the idle (assuming all else engine-wise is OK)

Or I might put in my GTR pump that I have - I don't know whats in there now but its noisy

Thanx everyone else too - I'll clean my AFM just for good measure

Link to comment
https://www.sau.com.au/forums/topic/65202-rb20-fast-idle/#findComment-1220349
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks Dose.....    I appreciate it!!
    • I'll probably be putting the shit box back on the dyno again soon, I want to dial in the closed loop boost control properly. I'll have a camera facing the car/motor for fun too. Just note, there are essentially 3x 10AN inlets going into the catch can and 1x going back to the intake pipe. Most of the time the catch can "return" to the sump actually is the crank case breather, pushing air out.
    • I have the R3C with a Nismo slave and by no means does it behave like a stocker, it ain’t THAT bad. On take off just give a bit more throttle than you would say a coppermix and it’s fine. It will not slip though.   
    • Okay. Final round of testing done. Got a friend to hook up a fancy scanner to the car and we also ran some compression and leakdown tests, she is healthy.  The MAF was definitely the culprit. So for future reference anyone with similar issues that find this thread. I suggest the following steps, in order of affordability:   Check your spark plugs for any fouling, replace plugs if they are bad or re adjust the gaps making it narrower (0.8mm would be good). Check every coil's resistance with a multimeter. It can be done by probing the IB and G pins on the coil pack. Resistance should be around 1.4 (+/- 0.1) Ohms Check the MAF. If you have Nissan connect or a good scanner with the 14 adapter it should allow you to see the voltage on the MAF reading should be around 1.1 - 1.2V when car is idling. But if you don't, buy a new MAF from Amazon and test, then return it. (For instance, I got a Chinese one for $40 that was reporting 1.3v on idle). If you still have scanner, you can run tests on the injectors to see if they are working, just remember to unplug the fuel pump fuse/relay and have no pressure on the line. Then listen for the noises that the injectors make. Clean/replace injectors as needed. Once you find the issue and fix, order thousands of dollars worth of OEM parts to refresh unrelated things (Optional)   PS: Thanks to the absolute legends of this forum for the responses and help to someone that went a bit over their head. (me)
    • Ha ha ha, so they stopped the bearings spinning on the one you want, but then decided the crank hub should slip instead 😛   Stick to RB, at least you can work on it yourself. And now it doesn't smell of vapour   Also I still believe there's a chance your new flap doesn't "pop", as even though the engine might breath hard, it has a direct path with no restriction to the inlet, which when on boost should pull a bit of suction for you. If you do get pressure in the catch can id be very intrigued. Time to put a boost gauge on it, and a session at the track, then solid cover your vent and do another session
×
×
  • Create New...