Jump to content
SAU Community

r32: rattling gone when on clutch?

whodaman
 Share

Recommended Posts

whodaman Contributor

whodaman

Posted
Posted

Hi,

Anyone know how to fix this problem?

I change gears fine. everything works.

There is this rattling noise that bothers me. I don't hear it when cruising along with the exhaust and radio going. But, while idling in neutral, I can hear a rattling noise maybe in the gear box?

The noise goes away when I step on the clutch.

What to do? Replace whole gearbox? Is it a flywheel problem?

my car is a 2.0 gts r32 4dr sedan, manual...

I had the gear box oil changed 2.5 years ago. I noticed the rattling in the last 3 months.

a mechanic says to wait until it goes then he'll fix it. somehow I think fixing it now is better than waiting for "it"(?) to go...

Thanks to anyone who helps.

Link to comment
https://www.sau.com.au/forums/topic/65248-r32-rattling-gone-when-on-clutch/
Share on other sites
OFENSV Proficient

OFENSV

Posted
Posted

mine use to do it but wasnt real bad. Clutch wore out not long after so i put new clutch and bearing in and was all good. depends how bad yours is. if it sounds like its about to seize id get it done soon as you dont want it to sieze and stuff your pressure plate

OFENSV Proficient

OFENSV

Posted
Posted
Ok.. i'll have to keep an eye out for gearboxes for sale...  thanks dude

why? the thrust bearing is part of the clutch. goes on the clutch fork, can buy them seperate or probably better of replacing clutch at same time. if it is that dont see why you need to look for a gearbox

SteveL Mentor

SteveL

Posted
Posted
I change gears fine. everything works.

There is this rattling noise that bothers me.  I don't hear it when cruising along with the exhaust and radio going.  But, while idling in neutral, I can hear a rattling noise maybe in the gear box?

The noise goes away when I step on the clutch..

Odds on it's a noisy clutch throw-out bearing. Cheap to fix...maybe $50+fitting, but it's been a long time since I bought just the bearing as it's usually changed when the clutch is replaced. Since the gearbox has to come out anyway to fix it, it would be worthwhile checking the condition of the clutch while its out.

I had the gear box oil changed 2.5 years ago.  I noticed the rattling in the last 3 months.

You're definately overdue for an oil change...I assume the level has at least been checked since it was changed ?? Still, if it's changing gears normally then it's probably just the clutch t/out bearing (above).

a mechanic says to wait until it goes then he'll fix it.  somehow I think fixing it now is better than waiting for "it"(?) to go....

A t/out bearing can be noisy for a very long time before it actually fails completely. Usually they just seize and the whole thing gets VERY noisy. Don't think I'd wait until it actually failed tho....

The Dan Grand Master

The Dan

Posted
Posted

The worse the carrier bearing gets, the more it can wear out the clutch. If it seizes, it'll wear down the face of the bearing, then the clutch won't fully disengage. Some don't get like that but it can happen.

If there were a problem with the gearbox, I would imagine you would be able to hear it while driving, as neutral is not a loaded position. More likely to be the carrier bearing. If the noise sounds bad then get it changed immediately. Get the clutch done at the same time as OFENSV mentioned.

Should cost around the $600 mark for an upgraded clutch fitted drive away.

Would prolly cost around $200-$250 to just do the Carrier bearing (which only costs about $15). It often pays to do the rear main seal while your in there but it should be ok if it's not leaking at all.

There is a test you can do to tell the difference between the carrier bearing and gearbox noise. Just rest your foot on the clutch to take up the free play. Don't push it to the floor. This will push the carrier bearing up against the pressure plate but won't disengage the clutch. If the noise goes away like before, then the carrier bearing is the one.

BiZzReVhEad Community Regular

BiZzReVhEad

Posted
Posted

yer mines goin too ... im gunna do it soon , so long as i can find meself a few hrs and no rain.

Do u need any specialized tools to get the box out ? i only got a few sockets and spanners :( .. oh and bugga gettin a mechanic to charge u 200 bucks to pull the box out !

RB30-POWER Mentor

RB30-POWER

Posted
Posted

The thrust/throw out bearing for the clutch only spins when the clutch is pressed in to the floor.

Yet you said the noise goes away when you step on the clutch?

Therfore it isn't the throwout/clutch bearing.

This is why you shouldn't sit at lights holding the clutch in as you wear the bearing out unnecessarily.

It will be one of two things.

One, its as simple as the input shaft bearing being stuffed. (Needs replacment)

Two, the hard casing has worn off the input shaft and main cluster gear in the box meaning all these parts will need replacing, therfore its cheaper to replace box altogether.

To rebuild it is going to cost some money. You would be better off to wait till it goes, then just replace it with another. RB20 boxes aren't worth much these days.

BiZzReVhEad Community Regular

BiZzReVhEad

Posted
Posted

sorry to sound like a dumb ass but wat ? i thought if the throwout bearing was on its way if u pushed the clutch in the noise would go away ...

Ur sayin its the input shaft bearing ? umm isnt there only 1 bearing (that big round one) and a bush in the bak of block (brass) where shaft goes . Wats the "Input shaft bearing" . now im scared . I should just grab a new box . There is a small wind in the gears to i not sure if thats all bearing either . Wat u think , just grab new box to be safe , i dont wanna put the new bearings on and put it all bak in to find out i wasted all that time for nothing

Sorry to hijak ur thread wodaman .. me havin same issues :)

BiZzReVhEad Community Regular

BiZzReVhEad

Posted
Posted

ummm , actually ... i was told that it is Actually the input shaft bearing .. John from UAS said thats wat was wrong wif my box . "welcome to nissan" he says :D damn it ...

So id prolly just get a new box in that case .

How would u tell if ur thrustrace bearing was goin then ?

RB30-POWER Mentor

RB30-POWER

Posted
Posted

When you press the clutch in, the clutch fork presses the thrust/clutch bearing into the clutch pressure plate fingers and the two parts of the bearings spin.

When you release the clutch the fork/bearing slide away from the fingers and the bearing spins as a complete assembly with the box input shaft. So it can't make any noise obviously.

If you press in the clutch in and its noisy then the clutch bearing would be shot, as the bearing will be spinning anytime the clutch is pressed to the floor.

If it isn't noisy it is fine.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      NC MX5

      By Dose Pipe Sutututu · Posted

      The German place in Cabramatta was rock solid, fresh pretzel cooked to order back then. Then it went all quiet, after all the poker machines were removed, then I believe it closed for good. I did drive past the other week and noticed outdoor lighting a big screen, but no idea what is there now.  
    • joshuaho96
      R33 GTR running -9 with no tune

      By joshuaho96 · Posted

      Yeah I suspect even if you hold airmass per cycle/cylinder constant if you get too far away from stock you're still going to have problems running the factory tune within the bounds of the factory load scale. Cams, different displacement/rod ratio, etc. I'm just lucky that the GTIII-SS with wastegate boost + CA compliance cats is pretty much equivalent to stock turbos. When I have actual space I can finally get it tuned and modify the fuel system for flex fuel to 100% handle any detonation concerns when cranking the boost to whatever those dinky turbos can put out.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      I would say no, why, because my daughter, who also lives in Goulburn, hasn't recommended us going there Pity, as we miss all the German joints around in Sydney, actually, the restaurants are the only thing I really miss about Sydney, and a special mention to Ishibanboshi at Bondi Junction, their Kara-age Don is heart cloggingly deliciousness (always added a special boiled egg...or 2) 😋 
    • GTSBoy
      NC MX5

      By GTSBoy · Posted

      Does that German restaurant still exist in the old place out the NW end of Goulburn? When I say "out the NW end of"...I am really being vague. It was 1997 when I was last there, and the only point of reference I can recall is that it was on the opposite side of the main drag from the big merino. And when I say "opposite side of the main drag", I don't mean "on the main drag". It was either a couple of streets back from there, or might have even been out in the sticks a bit further. Was an old farm building or mill or somesuch. And when I say "the big merino" I might actually be thinking of a completely different part of town, because I just looked on maps and the big bugger is not where I remembered him to be! The food was good, consisting largely of various German mystery-meat sausage/loaf things and kartofflen.
    • GTSBoy
      R33 GTR running -9 with no tune

      By GTSBoy · Posted

      So while the second sentence is completely correct and the whole point of the conversation, the first sentence bears consideration. If this bloke is just hoping to throw big turbos on and drive it around, because there are no helpful facilities at all in his tropical paradise** then he likely has zero chance of even knowing what the TP is on the last column in the stock maps, let alone know whether the ECU is operating anywhere near it or past it. So the point is very very moot. And, per what I said before, at stock boost on those turbos, you may well be off the end of the map. **I'm just back from Vanuatu, so I know exactly what small Pacific nations can be like wrt paradise without requisite facilities. But it's not even that simple. I put a high flow on my car and had to drive it around without a proper tune because of the lack of opportunity*** to put the bigger AFM and injectors into it to allow it to be tuned. I had to turn the boost down to less than I had before, and back off the boost controller's ramp, because it was exploring parts of the map that it didn't drive in before, and really couldn't access for tuning on the dyno either, and so was pinging. It was still well within the last column, because when I first**** set up the Nistune on the Neo I rescaled all axes of the maps to give some more space to explore. ***Family dyno was broken ****This was 13 years ago, and the TIM thing wasn't a thing then and so TP would definitely grow when pushing past the stock tune's limits.
×
×
  • Create New...