Jump to content
SAU Community

Recommended Posts

It is strongly not recommended to run your car hard until it's up to proper operating temperature.

I know with my kart racing that we shouldn't push it hard until the temp. is up as the piston will obviously be revving hard causing friction and in turn heat. When something heats up it expands, if the piston/ring expand and the cylinder doesn't (because it's in the process of warming the coolant/water around the cylinder) then it can cause the engine to brake.

Even though you have oil lubricating the parts, if something is heating/expanding at a different rate to another part it causes problems.

Espectually with turbos, as the compressor/turbine wheel heat up and expand, the turbo housing must expand with it.

It's like when in bed with a girl, if you put something fat and hard into...... u get the point :)

Yep, you need to work gently her to get her up to operating temperature.

If you don't then the lube won't be doing its job and you will chew out her lumps. :)

Water temp is irrelevant, once water temp is up to operating temp you then have to wait approx 7mins for the oil to come up to operating temp.

So if the Skyline is running correctly this will be around 10mins of driving.

Mine takes 2-3mins for the water temp to come up.

And dont forget that even if you warm up the engine's temps to operating range while stationary (eg in the morning), your gearbox wouldn't have had the chance to warm up and would need a few mins to catch up.

No never rev it till it's reached operating temp.

But hey if you do and u blow the motor which u will, I can find u a buyer who will take it off ur hands for cheap.

PS: I bought my gtst off a p plater who did exactly that, I snapped it up for real cheap :(

Especially if you run forged piston's, these are ment to be warmed up properly as they expand and contract in the cylinder, You can hear it when the car is cold if you try and rev over 3k it doesnt sound all their.

This is the same when you are running in you'r new forged piston engine, too much RPM = boost = air blowing past rings cause not run in properly.

As other's have said you'r just asking for trouble.

I dunno about no >2500RPM for 10 mins, there's no way I'd spend that long that low with my RB20DET, i'd never get anywhere! ;)

For me i just pay attention to how "hard" i drive it rather than keeping it below a set Revs amount, I'll rev up to 3500RPM odd but do it smoothly, no sharp acceleration or hard launches, until it gets warm! :(

exactly, if you keep it under boost it means your not gonna be pulling silly revs anyway.

by the way why would you want to drive your car hard when the water temp is cool? If you do boost it around when cold, the water temp will come up super fast anyways.

As for your 60 degree running temperature due to a better cooling system, what happened to your thermostat?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hang on. Let me get this straight. The desire is to have coilovers, BC in particular, to be MORE comfortable on Sydney roads than stock suspension? Well, that's obviously not right. BCs have crude damping design at the very best, and typically hard spring rates. BC stands for Billy Cart. And then, the desire is to put in some shitty old worn out stockers, to get it blue slipped and then put the BCs back in? And then.....what? Not worry about getting pulled up by the Plod? Because you seem to have raised a worry about paying for engineering (which actually does solve all your legality problems) and still getting pulled up.... but the only problem there is that if/when that happens you have to show your paperwork at the inspection station. Whereas, if you just swap in borrowed shitty old stockers to get it slipped now, and then you get defected in the future, you have to go find more shitty old stockers then too. You course of action looks like this set of options: Buy brand new stock type dampers, and springs. probably cost a bit more than $1k all up, but will last for the remaining life of the car. Put them in, pass inspection, drive on them forever more. Hell, they could even be really nice Bilsteins and Kings or other lower&stiffer springs if you wanted. Get the car engineered as is. ~$1k. Buy new Shockworks coilvers (or MCA) and also pay for engineering. You're spending a lot more here. But these will be the best things that you could drive around on.
    • Might be worthwhile hitting up Facebook's groups, I know most of them contain terrible people and scammers - however you might be able to find someone that's in Sydney with factory suspension you could purchase and/or hire. Just do not send any form of money anywhere, in person cash only.
    • Thanks @Duncan Ride height is fine. I think it's almost stock tbh. Happy to share a pic. I don't actually have a regular mechanic as haven't lived in Sydney too long. Could you or anyone recommend any shops in Sydney?
    • You just need a different blue slip shop (preferably one you regularly use as a mechanic), and make sure the coil overs are as close as possible to standard height
    • yeah the sugar refining companies were pushing for the same in Oz originally, all fuels were going to have 10% ethanol to make them "cheaper" (noting, that the loss in l/100 might be greater than the decrease in price). I guess they won that fight in Canadia
×
×
  • Create New...