Jump to content
SAU Community

Recommended Posts

It is strongly not recommended to run your car hard until it's up to proper operating temperature.

I know with my kart racing that we shouldn't push it hard until the temp. is up as the piston will obviously be revving hard causing friction and in turn heat. When something heats up it expands, if the piston/ring expand and the cylinder doesn't (because it's in the process of warming the coolant/water around the cylinder) then it can cause the engine to brake.

Even though you have oil lubricating the parts, if something is heating/expanding at a different rate to another part it causes problems.

Espectually with turbos, as the compressor/turbine wheel heat up and expand, the turbo housing must expand with it.

It's like when in bed with a girl, if you put something fat and hard into...... u get the point :)

Yep, you need to work gently her to get her up to operating temperature.

If you don't then the lube won't be doing its job and you will chew out her lumps. :)

Water temp is irrelevant, once water temp is up to operating temp you then have to wait approx 7mins for the oil to come up to operating temp.

So if the Skyline is running correctly this will be around 10mins of driving.

Mine takes 2-3mins for the water temp to come up.

And dont forget that even if you warm up the engine's temps to operating range while stationary (eg in the morning), your gearbox wouldn't have had the chance to warm up and would need a few mins to catch up.

No never rev it till it's reached operating temp.

But hey if you do and u blow the motor which u will, I can find u a buyer who will take it off ur hands for cheap.

PS: I bought my gtst off a p plater who did exactly that, I snapped it up for real cheap :(

Especially if you run forged piston's, these are ment to be warmed up properly as they expand and contract in the cylinder, You can hear it when the car is cold if you try and rev over 3k it doesnt sound all their.

This is the same when you are running in you'r new forged piston engine, too much RPM = boost = air blowing past rings cause not run in properly.

As other's have said you'r just asking for trouble.

I dunno about no >2500RPM for 10 mins, there's no way I'd spend that long that low with my RB20DET, i'd never get anywhere! ;)

For me i just pay attention to how "hard" i drive it rather than keeping it below a set Revs amount, I'll rev up to 3500RPM odd but do it smoothly, no sharp acceleration or hard launches, until it gets warm! :(

exactly, if you keep it under boost it means your not gonna be pulling silly revs anyway.

by the way why would you want to drive your car hard when the water temp is cool? If you do boost it around when cold, the water temp will come up super fast anyways.

As for your 60 degree running temperature due to a better cooling system, what happened to your thermostat?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Version 1 aluminium airbox is.......not acceptable No pics as I "didn't like the look.....alot" Even after all my "CAD", and measurements, the leg near the fusebox just didn't sit right as it ended up about 10mm long and made the angle of the dangle look wrong, the height was a little short as well, meh, I wasn't that confident that Version 1 was going to be an instant winner I might give Version 2 another go, there's plenty of aluminium at work, but, after having in on and off a few times, and laying in the old OEM airbox without the new pod filter and MAF, there may be an option to modify the OEM air box and still use the Autoexe front cover and filter.... maybe This >  Needs to fit in here, but using the panel, and not the pod, the MAF will need to fit in the airbox though> I'm thinking as the old OEM box and Autoexe cover that is sitting in the shed is just sitting around doing nothing, and they are relatively abundant and cheap to replace if I mess it up and need another, it may well fit with some modifications to how the Autoexe brackets mounts to the rad support, and some dremiling to move it get in there, should give me some more room for activities, as I don't want to move the MAF and affect the tune Sealing the hole it requires to stick it in the air box is simple, a tight fit and some pinch weld will seal it up tight  I am calling this a later problem though
    • and it ends up being already priced in as though you're just on 91RON without any ethanol. Car will lose a bit of economy as the short and long term fuel trims bring down the AFR back to stoich or whatever it is for cruise/idle for the engine.  
    • Oh, you are right. But, in Australia E10 is based on 91RON fuel and ends up being 94RON. Hence it being the cheaper option for economy cars. The more performance oriented cars go for the 98RON fuel that has no ethanol mixed in. The only step up we have left then at some petrol stations is E85.
    • There is a warning that "this thread is super old" but they ignore that anyway...
    • With 10% Ethanol, we're talking 2-3% fuel consumption difference. The emissions reductions and octane boost in my opinion far outweigh this almost non existent loss.    My tanks sitting at 80%. Luckily that should go down fast as I'm on vacation again for the next two weeks. 
×
×
  • Create New...