Jump to content
SAU Community

Recommended Posts

APEXi POWER FC +COMMANDER From $1000 Delivered

Brand New.

Most makes in stock

Regular Power FC + Commander:

- ECR33 Skyline GTS-t RB25DET

- ER34 Skyline GTT RB25DET

- BNR32 GT-R RB26DETT

- BCNR33 GT-R RB26DETT

- BNR34 GT-R RB26DETT

D-Jetro Type Power FC + Commander:

- BNR32 GT-R RB26DETT

- BCNR33 GT-R RB26DETT

- BNR34 GT-R RB26DETT

AP Engineering Power FC + Commander

- HCR32 Skyline GTS-t RB20DET

Power FC PRO Spec also available depending on model.

Other APEXi products are also available. Please email us for more information.

Please email us for enquiry.

[email protected]

Link to comment
https://www.sau.com.au/forums/topic/66452-apexi-power-fc-commander-980-shipped/
Share on other sites

  • Replies 101
  • Created
  • Last Reply

Top Posters In This Topic

APEXi POWER FC +COMMANDER $980 Shipped

- Brand New.

- Most makes in stock

- This offer is untill 20th of March 2005.

ECR33 Skyline GTS-t, $980 Shipped

ER34 Skyline GTT, $980 Shipped

BNR32, BCNR33 GT-R, $980 Shipped

BNR34 GT-R, $980 Shipped

D-Jetro Type also available with same price.

AP Engineering Power FC for HCR32 Skyline GTS-t RB20DET, $1150

Please email me for enquiry.

[email protected]

hey will the power fc and commander work in a r32 gtst??

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...