Jump to content
SAU Community

Would you pay $100 to rent an A/F ratio Meter?

Sydneykid

By Sydneykid,
in Engines & Forced Induction

 Share

Recommended Posts

Sydneykid Grand Master

Sydneykid

Posted
Posted

Hi guys, I have had an ever increasing number of people ask me about tuning their car without going to a dyno. They may live too far away, not have the budget or they simply may want to do it themselves. I have accumulated a few A/F ratio meters over time. I thought to help guys out, I might rent a couple of them out. They are not too expensive to buy, but the maintenance can be relatively high, you have to clean the lambda sensor and perform calibration regularly.

So......

How many would be interested in renting one for a week for say $100? That would cover maintenance and repairs etc. What you would get is;

*a wide band lambda sensor

*long lead to reach to the tail pipe

*a clamp for holding the lambda sensor in the tail pipe

*a meter and controller with sensor preheating for accuracy

*a mount and vacuum cup for attaching the display to the windscreen

*a cigarette lighter power plug & supply

*a full set of intructions

*a laptop interface and logging software to load (not necessary for tuning)

*all mailed out to you in an aluminium case

What you don't get;

*you are doing the tuning, if you damage your engine it's your problem

*if you get busted breaking the road rules, it's your problem

*I don't have time for dial up support, maybe email would be OK though

*insurance, if you break it or loose it, you pay for it

*a lap top, you supply your own, if you want to do logging

*credit, you pay up front and there will be a deposit (not sure how much yet)

*freight, you have to pay both ways, it's light, so $10 should cover almost anywhere in Oz

*instant supply, I only have 2 suitable units and I don't want to buy more. So you may have to wait until one becomes available

*to use leaded fuel, it must be unleaded

* to send it back dirty and greasy, clean it please

*your deposit refunded until it is received in good condition

This is a survey for me to judge the response, so post away. If I get enough interest I will be ready to go in about 3 weeks, as I would have to clean, service and calibrate the 2 units.

55Nat Enthusiast

55Nat

Posted
Posted

Awsome Idea,

I was charged $50 for 15mins of driving up and down the road I was not impressed I didn't get to load it up in top gears only 2nd gear.

Have you got any Second Hand/New ForSale ?

:P

Nat

RB30-POWER Mentor

RB30-POWER

Posted
Posted

If its a brand name unit such as the Autronic model, they are expensive, i say make people leave a deposit of $500 bare minimum, just incase something happens.

Because you know what people are like, hopeless.....

If you have a quality unit for hire now, i will hire it immediately.

$100 is a fair price for a week, + return freight/post to you.

You can get some preety good wide band units off the net now for around $500-$600 with controller, which is a great price if you want to tune your own cars.

Let us know either way.

Cheers

Sydneykid Grand Master

Sydneykid

Posted
  • Author
Posted
sounds like a very good idea :cheers:

Yep, I know it's a good idea, but how many people would actually rent one for a week for $100? That's the question, if I get enough I will do it. We can then start a thread on people's experiences with tuning on road and the results they get. Should make a good reference for others.

I need a few more to make it worthwhile, so let me know:cheers:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      RB26DETT Sketchy boost mod?

      By Duncan · Posted

      Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • nash47
      Cas issue

      By nash47 · Posted

      Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • nxh
      R34 4 door side skirt identification

      By nxh · Posted

      Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • GTSBoy
      boost source Size Garrett gt28 gen2

      By GTSBoy · Posted

      Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
×
×
  • Create New...