Jump to content
SAU Community

Recommended Posts

Hey guys, just did a minor service to the R33 GTST just wanted to know if i should have done anything different.

I put in NGK BCPR6ES sparkies with 0.8mm gap which i had a look through a few threads and it came up as the common gap measure.

or was it supposed to be 1.1mm like some other threads said? car is only like 190rwkw or less. also set cost $21 instead of $20 a plug for platinum or iridiums.

I haven't had any misfire or lagging issues and my friend who is a nissan mechanic but doesn't see alot of skylines at work said that to him its running fine.

Did the oil filter change aswell as get new oil. I used what my friend uses at the nissan shop some semi synthetic 10w vicuous rating. I wanted motul but couldn't find any on a saturday but he said that they use the same oil on S15's and 350Z.

We also had to change the Engine Temp Sensor and Thermostat cause there cause the idle kept spiking to 1500rpm in idle instead of 800rpm also the temp guage was fluctuating alot. Changed the Coolant aswell and used the Nissan Genuine coolant.

all that seems to have stopped now for 2 days so looks like that problem was fixed.

while the plugs were getting done we did a throttle body clean with this spray he had and blew out some black gunk residue.

anything that i may have missed like the plugs aren't gapped properly.

thanks.

oh aswell can anyone tell me how to get my boost to go right to .9 bar on load than having it stagnantly go up as i power through the revs and speed. basically when the car hits boost i want it to power right into .9 bar not .6 here .7 there. I saw on my friends Liberty RS that when it hits boost, whack straight to 1bar.

hope i discribed that ok.

yeah, you'll take it off, and then tip out the fuel that was in there, and it'll be like brown. like muddy water sorta colour!

I also changed the gearbox oil and diff oil, and, usual service, check all other fluid levels, check for wear on belts, check for any damaged/frayed lines.

If you're curious, also do a compression test, and if car has done 100,000kms, do the timing belt if it hasn't been done already.

Gap should only be set to .8mm when you are boosting 1 bar or more.

1.0 mm is fine for standard boost aplications.

You can remove the wastegate actuator and slot the holes to up the boost. It will come on more suddenly then before. I would not recommend doing this unless you know what you are doing as you might stuff it. Another trick is to set up a tight spring on the pod's arm, it will delay opening and give you harder boost but beware, it will spike a couple of pound before resting on your set value.

cool thanks for the replies

yeah sounds like the boost thing is going to be a bit too complicated for me so i'll have to take it to a performance shop and get it to check it out.

yeah the fuel filter was recommended by my friend but i don't have the money at the moment. he was saying like $160 to do the filter and the clean together but its on list to do in the next couple months.

yeah checked all the fluid levels and topped them up while we did everything else but didn't do the gearbox or diff, didn't think about it. piping and tubes were ok no cracks.

timing belt was changed at 94,000 kms, 20,000kms ago.

now reading this O2 sensor thread that came up i'm damn keen to do this cause i got bad fuel economy.

What do you mean $160 to do the fuel filter? It costs about $30 from Nissan and you do it yourself. Take clamps off each end and while you're replacing it just plug the fuel line.

$160 sounds more like changing the fuel pump!

I also would check my AFM (if you haven't) and clean the build up off it with electrical contact cleaner or something similar

Best way to get the boost response you describe is to go some sort of electric boost conroller. It will hold the wastegate shut untill it reaches your set level (Without the creep you get with cheep-o bleed valves)

$160 sounds more like changing the fuel pump!

yeah thats it, and a fuel injector clean through some machine.

now just double checking AFM what is that? is that the ECU electric housing area?

 Best way to get the boost response you describe is to go some sort of electric boost conroller. It will hold the wastegate shut untill it reaches your set level (Without the creep you get with cheep-o bleed valves)

yup thats sounds alot like what i need to fix my problem, what sorta boost controller you reckon i get cause i think i have the cheapy $90 job attached to some wires in the engine with the turning knob.

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...