Jump to content
SAU Community

Recommended Posts

Hey everyone,

if you have a catch can with only two outlets on it where do you juction into the breathing system on an rb20???

i'm looking at something like this on ebay, seems as good as the rest?

http://cgi.ebay.com.au/ws/eBayISAPI.dll?Vi...4550437345&rd=1

Thanks

George

  • Replies 160
  • Created
  • Last Reply

Top Posters In This Topic

Hey everyone,

if you have a catch can with only two outlets on it where do you juction into the breathing system on an rb20???

Thanks

George

Hi George, you can, you just join up the 2 outlets from the cam covers with T piece and use the other can outlet to join into the breather system. It isn't as neat as buying one with the right number of outlets.:stupid:

Hi All,

I have searched and read numerous threads regards oil catch cans and am looking for a bit of direction. Most seem to acknowledge that the standard (cheapie) catch cans are nothing more than a can (no internals) and need to be stuffed with a filter (steel wool / scourers etc) in order to actually do what they are supposed to do - seperate oil from air and catch the oil. There are a couple of catch cans (more expensive- such as the Essential and ARC cans) which replace the washer bottle (GTR's only I think) and apparently do all they are supposed to do. These cost around $400-$500, which isn't exactly cheap. I have also seen the air/oil seperators (cylinder type) which fit across the top of the engine (GTR). From what I've been told, you also need a catch can with these to collect the oil. This type of air/oil seprator and cheap catch can would work out to be much cheaper than the expensive unit "which does it all". Question are-

Is this setup better or worse than the expensive catch cans?  

Do the expensive ones do everything they claim to?

Apart from reducing octane rating and performance, does oil blow back damage anything?

Thanks for your help.

Hi, we make custom surge tanks & breather cans. Can must be baffled so oil runs down to bottom of can & not straight out filter. if you email me at [email protected] i will send you some photos.

  • 2 months later...

I bought one of these from Unique Autosports on the weekend. I was going to buy the GReddy one (big and empty..), but John recommended this:

gtstcatchtank.jpg

It is baffled, and has a big hole up the middle of it (you can see it in the pic), there's a slight gap at the top of this where I think the thing vents to the atmosphere. But because it vents from underneath you can't really see anything "illegal".

Now after reading this thread I think I've installed it correctly, but I'm not sure.

CRW_1063_Medium.JPG

I haven't actually blocked anything off. Should I?

Also, I've left the blue screw in plug (drain) at the bottom of the catch can on.

Did I install it right?

**EDIT: figured out sk's drawings. All fixed now :D

  • 3 months later...

Well although I have an SR20DET, that install looks wrong. You've basically just looped it back into the cam cover again!

What you need to do is join the breathers on both sides together first, so that they _both_ go into the inlet of the catchcan. Then the outlet goes straight to the turbo.

Excuse the crap diagram but I hope you get what I mean;

catch.bmp

Edited by Busky2k
  • 6 months later...

Hi,

Sorry to bring this thread back from the dead but I just have a quick question about the pipe from the passenger side cam cover to the turbo inlet. Is the lump in this pipe a PCV Valve? shown below.

post-13456-1148790456.jpg

Thanks

nar buddy thats the return line to the turbo the same spot but on the other side of the motor ul see a lilttle hose that looks like an s thats the pcv conecting into the head my can is set up with the two hoses cuming of the top like the others but the return line is caped off inside that pipe and on the bottom of the catch can it has a nothere hose cabel tied down agenst the sump as if its going back in to the sump so if the cops look or pull on it it looks conected also the set up with 1 pipe going from the can then back to the return line wots the point in a none race enging bout 90% of wots runing through the lines is vapor witch is runing shit back through the turbo hence sucking in in pure air prity well defeting the pourpes of having a can to start with

Thanks Dave :cheers:

I knew there was a pcv valve on the plenum side just wasn't sure if on the other side it was a PCV Valve or just some re-inforcement for the pipe so it isn't collapsed by the suction. Would I be right in assuming that this inlet pipe is sucking all the time.

I was thinking about installing my can this way. The PCV Valve in between the catch can and the plenum is the one from 'A' on the side of the cam cover. Will just need a male/male hose connection of the right size to replace it I guess. Would be putting a stocking filled with stainless steel wool inside the can too.

post-13456-1148812199.jpg

I had thought about installing it by putting something inside the S-shaped pipe to the plenum and then blocking the turbo inlet pipe. Then running a hose from the passenger side cam cover to one side of the catch can and the 2nd outlet down to near the sump. Just thought if pulled over then I shouldn't have any trouble with the top way.

  • 3 weeks later...

RedDrifter, the only problem with that is if you don't disable the PCV, it'll pull air thru the catch can on light loads due to vacuum and thus you got a nice vacuum leak. I run my catch can atmo from 3 points, and disable the PCV. Works perfect.

pplo, that setup is plain wrong. It doesn't achieve anything.

ok no worries..

just to clarify,, this is what i intend to do ..

the blue pictures are screws showing blocking off the pipe..

with the pcv, im planning to cut it in half (green line) then block off each path (blue screw pics)..

post-29258-1150689843.jpg

would all of this be ok??

thanks!

Edited by pplo

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...