Jump to content
SAU Community

Recommended Posts

Hey Guys

I am selling these parts and require your standard parts in exchange.

I will pay for the conversion.

The prices are what was paid late 2003 and 2004.

Parts have travelled about 20,000 kms from new.

Apexi GT-Spec Drag Intercooler $3500

Nismo 600cc injectors $1500

Nismo internal fuel pump $600

Nismo fuel regulator $300

Bosch external fuel pump/swell pot/system $1400

Apexi dual N1 exhaust system $2200

HKS oil cooler $1600

HKS dump pipes $1000

Trust EO1 Boost controller $1100

Nismo turbos $5000

HKS 264 in/out cam shaft $1500

HKS drag pro valve springs $700

N1 oil pump $650

N1 water pump $250

Modified sump for oil surge $750

JE forged pistons/shot peened rods/head porting $12,000

HKS head gasket $1100

Motec M48 PRO ECU/harness/mapsensor $6500

OS Giken triple plate clutch $3000

Blitz BOV $750

HKS Cam gear $400

46K value.

I need 22K plus standard parts.

Car is here in brisbane.

Michael 0414561121

Link to comment
https://www.sau.com.au/forums/topic/68405-bargain-600hp-gtr-upgrade-package/
Share on other sites

T88 ON BOARD: Read the post. The prices listed are only an indication of what he paid initially. Hes offering the package for sale for approximately half of what he paid.

I'm selling up my cars. I own a few GTRs and am off-loading them as need cash for property.

Wife and kids sick of the cars.

Different priorities now.

Cars must go!!

Guys, I've bought a set of wheels off this guy before, spoken to him on the phone and seems like a very reasonable and honest bloke...

So give him a break and unless your interested in what his selling, keep your irrelevant comments to yourself!!!!

Some of us are just wanting to keep an eye out for others around here. I also saw this guy try and sell parts off a car that wasn't even in the country (wasn't even a 15 year old eligible import).

rb31, please post pics of these parts.

Hey Guys

I've been around too long to get caught up in a fear/smear campaign. I don't have a credibility issue. I am the guy in the Serious Performance 6 DVD with the yellow Abflug if that helps any.

I am in negotiation to sell the parts now. I hope the moderator has the decency to clean up this thread.

Thanks

Michael

Happy to clean up the thread, I hope you now have the decency to answer my questions

The parts you posted forsale in the other thread were they in Australia and owned by yourself?

Are you a importer/trader?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...