Jump to content
SAU Community

Recommended Posts

Problem with my car, its a R32 GTR...The other day i blew a heater hose having replaced that which was not easy. I took it for a drive and within 5mins the oil temp was around half about 150'C, its normally on the 70'C mark, the engine oil level is fine. the water temp was normal but there is oil in my radiator?? the oil pressure was going up and down and it still goes as good as it use to...i think it may be a blown head gasket or the oil pump is rooted, any suggestions would be great.

Link to comment
https://www.sau.com.au/forums/topic/69533-problem-with-gtr/
Share on other sites

It does sound like a gasket or oil pump problem which is why the heater hose may have come off in the first place. Whatever it is, it sounds bad. I would not do any more driving in it at all and get it towed to a workshop that knows what they are doing.

You could start off with a compression test to see if it is a head gasket. What were you doing prior to the heater hose blowing?

Link to comment
https://www.sau.com.au/forums/topic/69533-problem-with-gtr/#findComment-1286308
Share on other sites

The radiator fluid looks like a chocalate thick shake from Maca's, this all started when i took my car to get a dyno tune done. they tell me they didnt run it on the dyno but i drove past the place later n i saw my car up on the dyno. then mid arvo i got a phone call from them saying they found oil in my radiiator, they didnt even charge me anything which is a bit suspect...Well i blew the hose doing burnouts in RWD

Link to comment
https://www.sau.com.au/forums/topic/69533-problem-with-gtr/#findComment-1288086
Share on other sites

  • 2 months later...

Normally I have found blown headgaskets (ie Water in oil) to have a distinct smell, have you checked under the oil cap for milky residue or bubbles in radiator, which are a couple of giveaways :)

Has the car ever had its cooling system flushed and refilled with coolant since ownership....if not now may be a good time.

Static burnouts are probably the worst thing you can do to any engine, so it would not be suprising if you have blown your head gasket ;):D

If all else fails Whack some chemiweld or Bars leak in there she'll be good as new :P

Link to comment
https://www.sau.com.au/forums/topic/69533-problem-with-gtr/#findComment-1432562
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • When you crank your car, and hit it with a timing light, can you see a steady crank timing?
    • Oh, forgot to add, A few months ago I was getting mixture codes and the car was using crap loads of fuel. You could smell the unburned fuel in the exhaust, it was crazy strong. Economy was over 17.5 l/100 and usually around 19. I smoked the engine and found a leaky CCV hose which I replaced and then I replaced my two pre cat O2 sensors, I also replaced the MAF. This fixed my mixture codes and improved my exonomy but I'm still 14 - 15 l/100 when pottering about town so something is still amiss. Throttle response is much better and it has more pep but I'd like to know why it's still so thirsty (and I'm hoping that whatever it is gives me a bit more poke).    
    • Car is on factory injectors/z32 maf/ q45 throttle body/ z32 ecu with nistune 
    • Hello all, currently finishing up a rb25 swap into my s14. Having issues with starting, car has spark (confirmed by pulling a plug and watching it spark), has fuel(confirmed by checking pulse/voltage at injectors all spark plugs are soaked in fuel). Car cranks over and pops into the exhaust with a heavy fuel smell but no attempt to start or run, I have torn the timing cover off and triple confirmed timing, turned the CAS in multiple spots both directions, attempted to start with coolant temp and maf unplugged, checked my fuel lines and made sure they weren’t backwards, checked voltage at cas/injectors/coilpacks, made sure all the grounds in the harness are connected and added a few grounding straps (1 from chassis to block, 1 from chassis to head, and 1 from chassis to igniter chip) I am getting stumped here. As a last ditch effort I made a full grounding harness tonight that’s going to run from the battery and add an extra ground from the battery onto the coil pack harness/igniter chip/ intake manifold/ Wiring specialties harness ground/ and alternator. I’m hoping maybe the grounding harness will fix it here but posting here to see if anyone has any other ideas on what else I can check. My fuel pressure is unknown right gauge will be here tomorrow.  IMG_3206.mov
    • yeah I was shocked when I checked my spare OEM on and as below that's how they come from Nissan. (side interesting note new NEO gearbox and replacement park lack the brass bush on the tips and its just all alloy) unsure about damage to the box currently back at 1110 to be pulled down/inspected and selector fork replaced as he built it previously and given the never before seen failure on his billet forks he is replacing it under warranty. He said he has used always OEM the keyway tab without issue for years so it could be an unlucky coincidence. I did talk to him about the sharp corners and stress concentration too. Re: hard shifts i got 7+ years out of the OEM one and the fork itself failed not the keyway. so could be bad luck as I said or an age thing + heat cycles in box and during fabrication of billet?
×
×
  • Create New...