Jump to content
SAU Community

Recommended Posts

These catch cans look a hell of a lot better and more effective than my current setup. gR33ddy, will you be undertaking another group buy of these catch cans, or are they available through you at this price at any other stage soon?

Catch cans are still available.

PM sent.

  • Replies 94
  • Created
  • Last Reply

Top Posters In This Topic

PM received, my bank account balance is being monitored at the moment to see if I can afford one this week ;)

Possibly a stupid question, but I can't quite grasp the method used to fill the catch tank with steel wool. I read the threads linked to in the first post - how big is the opening underneath that filter if you can stuff baffling into it? Also, was it the pot-and-pan scrubber you use, or hardcore steel wool?

Cheers from a n00b.

Adrian

PM received, my bank account balance is being monitored at the moment to see if I can afford one this week :D

Possibly a stupid question, but I can't quite grasp the method used to fill the catch tank with steel wool. I read the threads linked to in the first post - how big is the opening underneath that filter if you can stuff baffling into it? Also, was it the pot-and-pan scrubber you use, or hardcore steel wool?  

Cheers from a n00b.

Adrian

The opening is approx. 1cm (inner diameter)

After you have fed the foot of the stocking in, using hardcore steel wool (pulled apart so it is stringy-like), stuff it gently in with the blunt end of a wooden skewer bit by bit. Being carefull to not rip the stocking and after this, tie the stocking(remove excess) and stuff the end in aswell.

It is tedious but is very possible and should be effective.

;)

to work effectivly the inlet should enter the can at the top and and turn down inside to finish up 2 or 3 mm from the bottom. the outlet just goes to the top. can should be filled with stainless steel wool. The ribbon type is best 'cos the flat with sharp edges helps to separate the oil from the air. Oil laden air is released at the bottm of the can and flows UP to the outlet depositing oil on the the wire wool as it goes. Search the for sale thread ...there was a very good one offered for sale a while ago.

  • 1 month later...

oz_cefiro - Should still be available then.

I have a new range of greddy style catch cans available aswell.

Heres some pics.

greddy-oct.jpg

colours available

greddy-oct2.JPG

These are $110 delivered.

:P

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...