Jump to content
SAU Community

Recommended Posts

  • Replies 61
  • Created
  • Last Reply

Top Posters In This Topic

hehe thats cool. ok the graph i have at home from memory the stock one was about 6000 ish that was in km/h at 141rwkw. since mods i *think* the peak power "flat spot area" has moved down a bit towards 5000/4500 ish, maybe its too low like you said, im going off the top of my head. will post the graph tonight so you can see. the peak power comes in and it stays at that level for a bit then drops off. will post the graph after club meeting

** removed all my other posts so that im not whoring your thread **

[ rb25det dyno runs and average power "info" ]

141rwkw stock everything

http://members.dodo.com.au/paul/skylinesau...tralia/lwf0.jpg

171 rwkw with knock and running rich

http://members.dodo.com.au/paul/skylinesau.../protek-171.jpg

172 rwkw with knock fixed and leaned out a bit

http://members.dodo.com.au/paul/skylinesau...-172-edited.jpg

from the second graph it looks like i have more peak power a bit earlier. by more peak power i mean within 5~ rwkw of my max power of 172. So from 130km/h onto 170km/h i have around 165rwkw. here's what i mean

http://members.dodo.com.au/paul/skylinesau...2-peak-area.jpg

----------------------------------------------------------------

255/40/17 Dunlop Direzza DZ101

(From roy's calucations)

Ok so:

3,500rpm - 106km/h

4,000rpm - 121km/h

4,500rpm - 136km/h

5,000rpm - 151km/h

5,500rpm - 166km/h

6,000rpm - 181km/h

6,500rpm - 196km/h

7,000rpm - 212km/h

7,500rpm - 227km/h

Max out from the rsm after dyno run (so its about 11km/h off the caluations)

http://members.dodo.com.au/paul/skylinesau...ia/dyno-run.jpg

You said yours makes 100rwkw at 2000. My rb25 makes 100rwkw at around 3300rpm from Roy's calculations. Go the rb30! :Phttp://http://members.dodo.com.au/paul/skylinesaustralia/172-peak-area.jpg' target='_blank'>

i dont have an exact "what rpm is 130 to 170km/h" range is so its hard to work out. i recall sydneykid showing a chart on how to calculate it, will try and find it and post up what i find

http://www.skylinesaustralia.com/forums/sh...59&postcount=51

shows a rpm vs km/h for a gtr (should be in 4th with same diff ratio?)

my avg of around 165ish looks to be around 5000 to 6200. its a bit of an "if" and "um " and "arrr". would anyone be able to give exact figures based on diff ration in 4th

 "What size tyres do you have? For example if your rears are 235/45/17s, and your run was in 3rd gear then...

 

  3,500rpm , 73km/h

  4,000rpm , 83km/h

  4,500rpm , 93km/h

  5,000rpm , 103km/h

  5,500rpm , 113km/h

  6,000rpm , 124km/h

  6,500rpm , 134km/h

  7,000rpm , 145km/h

  7,500rpm , 155km/h"

 

hi roy,

can you work this out for my car? 255/17 on the rear (sorry to hijack cubes)

Oops, edit

Ok so:

3,500rpm - 106km/h

4,000rpm - 121km/h

4,500rpm - 136km/h

5,000rpm - 151km/h

5,500rpm - 166km/h

6,000rpm - 181km/h

6,500rpm - 196km/h

7,000rpm - 212km/h

7,500rpm - 227km/h

Thats assuming your tyre has the same rolling diameter as a 255/40/17 Dunlop LM702...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...