Jump to content
SAU Community

Recommended Posts

Hey everyone, Ive just imported a stock r32 GTST with 46,000 kms on the clock, its in awsome condition. Just would like some advice as im new to this caper about some first up mods which i should consider? where do i start?

I figured first should be things like sports muffler from turbo back, and a pod filter? but all in all i wouldnt have much of a clue :Oops: So any advice would be very benificial to my cause many thanks

Link to comment
https://www.sau.com.au/forums/topic/70353-new-r32-gtst-what-to-get/
Share on other sites

There's SOOO many threads on this so go for a search.

But IMHO forget you should about a pod, upgarde the panel filter if you really must.

A 3" cat-back at the minimum, 3" front-pipe if you want a bit more, and maybe a larger dump if you intend to take things further later on.

Then a FMIC. Then you can put a little more boost thru it.

That should get you started.

I'd invest in a 100,000km service because your car will not be a gueniune 46,000km car unless its been sitting in a musuem in Japan. Thats less than 4,000km a year!!!

I've had five imports and I reckon every single on of them was wound back.

Believe me a major service will be alot cheaper than letting your timing belt snap

Hey mate, im ensure u its only done 48,000 kms! ive had it toally checked out all seems to in right. But yea i was thinking of getting a totall service done anyways cause eben still a car whicj hasnt been driven much at all still ages and will need some work. Thanks for the concern mate.

I'd invest in a 100,000km service because your car will not be a gueniune 46,000km car unless its been sitting in a musuem in Japan.  Thats less than 4,000km a year!!!

I've had five imports and I reckon every single on of them was wound back.

Believe me a major service will be alot cheaper than letting your timing belt snap

Hey mate thanks for the msg, as soon as its complied, i was going to have the timeing buslts worker over, they are in good nich as they are ! my machanic said should look at doing them in the next 1 or 2 services. but better to be safe then sorry thanks mate

first you should sell me your nice clean interior:P

other than that as people have said exhaust, fmic, maybe bleed valve and boost guage

also get an alarm with at least 3 point immobiliser....

I've heard the fuel pump has a few reliability issues, so it's a cheap upgrade to protect leaning out and the engine going "bang".

I'm in the process of buying a R33 GTST.. I intend to do a whiteline works kit (www.whiteline.com.au) suspension as my first mod. That way, you can learn to drive the car with the stock power, and to control it properly under power, and then do exhaust / bleed valve, followed by FMIC...

Everyone has their own ways of modificatons though, it's really up to you :D

Congrats on the buy mate! A car like that with genuine kilometres that low would be a rare beast indeed! Like a few others have said, make sure you invest on a decent alarm system for your car, that would really have to be a priority.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • What does it look like with highway driving? And yes, I had a similar thought as Duncan. It looks quite similar in my Stagea and I have made myself accept it as normal. Might have to look into it some day  
    • While I was waiting for the new parts to come in for the charge pipe and radiator I decided to do some turbo modification. The drive pressure (exhaust backpressure) was a lot higher that I thought it should be. For 32lbs of boost drive was 55lbs. The turbine housing is a 1.10AR and my turbo builder has suggested to go to a 1.25AR. To test if a larger AR would do anything to reduce drive pressure AND not spend any money I decided to hog out the divider in my current housing. I removed it from the inlet and the whole way through the housing.  After reassembly and testing it doesn't look like this modification did anything for reducing drive pressure or requiring more fuel (making more power). Oh well, it was worth a shot. We'll get some data at the track if it makes it past the 60ft. I also machined a $7 shift knob off Amazon to fit my Stillway shifter since I didn't like the Stillway shift knob. Next on the list was the radiator replacement and fabrication of a new intercooler tube that had no silicon coupler. No pictures of this - I was short on time each night after work to get this done and didn't stop to take pictures.  Next was to get the clutch disks out and replaced. Previously when installing the dogbox I had ordered a set of the same sintered iron disks I had been running because I switched to the 26-spline input shaft. I thought it was odd that they didn't have any markings or brand name on them like all my old disks had but installed them anyway. At the track I could not get the clutch to lock up using my normal strategies. After two track nights I reached out to the clutch manufacturer and ask their thoughts. They said they had to switch the material out because they were having trouble getting the original material and that this new material would not take to being slipped very well.  So out with the first set of 26-spline disks and in with the correct material 26-spline disks. While I had the trans out I added an inspection/service hole. I've wanted one of these for a while. Now I can have a look at things and change the front cover shimming when needed (clutch wear). I hustled and got the clutch change done in a few hours on a Saturday. Hopped in the car and drove home. On the way home I did a 1-3 pull. When shifting from 2nd to 3rd the core plug in the back of the cylinder head popped out and dumped all the coolant. Thankfully I was only 30 seconds from home and coasted it there. Datalog showed nothing unusual and 2.5psi of coolant pressure. That plug has been in there since 1992 but I guess it worked its way out. Pulled the trans AGAIN and replaced the plug, JB welded it in, and made a brace. Also deleted the head drain I had added in during the bearing issue fiasco.  I am currently changing my boost control plumbing to make it cleaner. After that is done I'll make another attempt at getting past the 60.
    • Are you 100% sure this isn't tune related?
    • 140-150 across the board. At this point hoping the grounding harness fixes it. My grounds are all tied to the chassis and none to the battery. For SR and KA that’s never been a problem for me but had a few other guys here and Reddit who told me RB really like a very solid ground setup tied to the battery so going to try that next, I’m stumped if that doesn’t do it. Never had a car have spark and fuel and not fire off before. Only thing I can think is the spark is intermittent/weak because of grounds nothing else really makes sense at this point 
    • I am having close to the same issue. Can you help me with what wire you grounded to get your pump to trigger?
×
×
  • Create New...