Jump to content
SAU Community

Recommended Posts

Ok so im planning my new install on my R32 GTS-t and just wanted the heads up on any trouble that anyone may of experincied in the past so i can plan ahead. Im planning on running a Pioneer 5750 HU with Pioneer components in the front doors replacing the stock speakers. I have another set of splits that im going to put into the rear parcell shelf. I have 2 MTX Thunders that i was thinking of using, can't decide if i want to run both in one box, 1 in a sealed box, 1 in a tube or two in the existing sub box, 2 in 1 tube or 2 in seprate tubes??? I plan on installing my new amp and hear that you either have to bypass the old amp or run new speaker cables, whatever is easiest i will do, but as im thinking of running the front splits of the head unit i dont see that as being a problem at all. Anyway just after anyones advice on the general install, how to and where to install and what you used for it in general?

Cheers GMB

Link to comment
https://www.sau.com.au/forums/topic/70445-r32-install/
Share on other sites

U cant get anything bigger than a 6" speakers in the fron doors. ( in there stock hole anyway)

A little hard getting wires throught the file wall. but not 2 hard, nothing a coat hanger cant fix.

That's about all i have to say about problems I had on my install.

Link to comment
https://www.sau.com.au/forums/topic/70445-r32-install/#findComment-1301208
Share on other sites

as madtrang said the main problem is running cable throught the firewall, but its not that bad.

You'll need to make up some MDF mounting plates for the fronts. Just use the stock ones as a template.

I just ran new wires to all the speakers and bypassed the factory amp.

As for subs, it depends on how much boot space you can afford to lose. I need to fit a set of golf clubs in mine so I've got a small sealed box between the shock towers.

Head unit is pretty easy, just get the right wiring diagram off the net. I had to drill new mounting holes in the factory cradle to make my head unit sit flush with the a/c controls.

Let me know if you need any more help as I just finished my install last weekend.

Link to comment
https://www.sau.com.au/forums/topic/70445-r32-install/#findComment-1301366
Share on other sites

U cant get anything bigger than a 6" speakers in the fron doors. ( in there stock hole anyway)

A little hard getting wires throught the file wall. but not 2 hard, nothing a coat hanger cant fix.

That's about all i have to say about problems I had on my install.

No prob's with getting cables through the fire wall, im used to doing the impossible, apprentice sparky by trade :headspin:

As for not getting anything bigger than 6" in the fronts isn't exactly right as we got a pair of 6X9's in my mates R32 no probs, but yes it did take modification of the existing speaker holes, nothing to drastic though. :)

Link to comment
https://www.sau.com.au/forums/topic/70445-r32-install/#findComment-1302061
Share on other sites

as madtrang said the main problem is running cable throught the firewall, but its not that bad.

You'll need to make up some MDF mounting plates for the fronts. Just use the stock ones as a template.

I just ran new wires to all the speakers and bypassed the factory amp.

As for subs, it depends on how much boot space you can afford to lose. I need to fit a set of golf clubs in mine so I've got a small sealed box between the shock towers.

Head unit is pretty easy, just get the right wiring diagram off the net. I had to drill new mounting holes in the factory cradle to make my head unit sit flush with the a/c controls.

Let me know if you need any more help as I just finished my install last weekend.

Where abouts you find the wiring diagram for the install and do you have a diagram for the amp bypass at all?

:)

Link to comment
https://www.sau.com.au/forums/topic/70445-r32-install/#findComment-1303788
Share on other sites

Hmmm ive got 6 1/5" splits in my front doors, and they fit pretty good..

Wiring diagram? What for... Multi meter finds waht you need..

If you can avoid running the front splits off the head unit and amp them do that, becuase if your gonna have the subs in there, you want the power to your speakers to keep up with the bass. If anything, dont amp the rears, as they are just for fill.

Ive Installed my stereo in and out of my skyline and old cars heaps... so if you have any Questions Just PM me...:cheers: Good luck

Link to comment
https://www.sau.com.au/forums/topic/70445-r32-install/#findComment-1304281
Share on other sites

hmmm on my r32 i was able to fit 6 by 9s without any body mods just made up mdf backing.... only problem you would have is with clearance behind... depending on the mounting depth.... mine were like 78mm so they fitted up fine but i had to use 18mm and they cleared the windows but door trim wouldnt go on... if they were like half a cm smaller should have been able to fit them on problems... so it would depend on the size

but then again 6.5 inches speakers are way better

gotta do my install this wkend

Link to comment
https://www.sau.com.au/forums/topic/70445-r32-install/#findComment-1314664
Share on other sites

amp wiring can come through the drivers wheel well. there is a body grommet inside it that will allow a decent sized cable through it.

SO does that mean your running the cabling outside underneath the car?

Link to comment
https://www.sau.com.au/forums/topic/70445-r32-install/#findComment-1316010
Share on other sites

here is the link for the wiring diagram.

you don't need a diagram to bypass the stock amp, just run new wires from your head unit/amp to your speakers.

Is it worthe ripping out the old amp while im doing it?

Link to comment
https://www.sau.com.au/forums/topic/70445-r32-install/#findComment-1318317
Share on other sites

I didn't bother ripping out the old amp cos it wasn't in the way of anything I was doing. I guess you could take it out if you really wanter to save an extra kilo.

And with the cables, no don't run them under the car, just under the carpet. That grommet Chris Rogers is talking about ends up on the inside above the accelerator pedal.

Link to comment
https://www.sau.com.au/forums/topic/70445-r32-install/#findComment-1318413
Share on other sites

I didn't bother ripping out the old amp cos it wasn't in the way of anything I was doing. I guess you could take it out if you really wanter to save an extra kilo.

And with the cables, no don't run them under the car, just under the carpet. That grommet Chris Rogers is talking about ends up on the inside above the accelerator pedal.

Oh ok, im with you. I'll ook into that, and i'll ahve to rip out the old amp and relocate the rear wiper assembly motor so i ahve enough room in there for my gear :wassup:

Link to comment
https://www.sau.com.au/forums/topic/70445-r32-install/#findComment-1318492
Share on other sites

don't bother with speakers in the rear if it's a GTS-t. They're not necessary and you'll save money.

The only reason i was going to put them in is cause i got em and there jsut sitting there but your right, you dont need them. Set of components up front with twin 10" MTX Thunders in the boot should do for now :headspin:

Link to comment
https://www.sau.com.au/forums/topic/70445-r32-install/#findComment-1319365
Share on other sites

Anyone got pics of the boot install with there sub box at all, after looking at the minimal room and height it limits your options and was wondering what everyone else had done to over come this? Post em up so i can get some idea's or just throw your ideas this way :rolleyes:

Link to comment
https://www.sau.com.au/forums/topic/70445-r32-install/#findComment-1330907
Share on other sites

don't bother with speakers in the rear if it's a GTS-t. They're not necessary and you'll save money.

personally, after listening to my system in the car after a week or so, I'd still greatly prefer a couple of speakers for rear, even if they are very basic and not high end ones. The sound appears to come much more "around" you, and I like that effect.

Just like at home I prefer 4 speakers powering my music at the one time.

Link to comment
https://www.sau.com.au/forums/topic/70445-r32-install/#findComment-1331057
Share on other sites

personally, after listening to my system in the car after a week or so, I'd still greatly prefer a couple of speakers for rear, even if they are very basic and not high end ones. The sound appears to come much more "around" you, and I like that effect.  

Just like at home I prefer 4 speakers powering my music at the one time.

I was thinking the same thing pred and the way i see it i already have the speakers so i may as well throw them in there and make use of them!!!

Link to comment
https://www.sau.com.au/forums/topic/70445-r32-install/#findComment-1331553
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I got a full sheet set of OEM copied stickers to replace all the faded engine bay ones, great quality too.  Came from England. Someone like that should be able to to make u up what u want so long as u have a quality image to show them 🤷🏻‍♂️
    • Did this end up working? Did you take some pictures?
    • And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
×
×
  • Create New...