Jump to content
SAU Community

Recommended Posts

Just buy a proper dump pipe, get a split type if you really must, BATMBL has quite a few on offer here: http://www.skylinesaustralia.com/forums/sh...ead.php?t=15558

costwise i don't really want to spend another 200 bucks plus for an extra piece of metal when I can use the gas axe, welder and a bit of pipe for about 50 bucks.

also i reckon that if i plum it close to the cat (as far away from the turbo, this will give better turbo efficiency because there is less turbulence. Thats the idea of the screamer isn't it?

what you guys reckon?

Link to comment
https://www.sau.com.au/forums/topic/70955-screamer-pipes/#findComment-1308991
Share on other sites

The concept of screamer is when the wastegate dumps the excess exhaust gases to atmosphere. This is why it is called a screamer pipe.

It is recommended to plump back as far away from the turbo as possibble. This will reduce turbulence. For legal reasons this must be before the Cat converter.

Hope this helps

Link to comment
https://www.sau.com.au/forums/topic/70955-screamer-pipes/#findComment-1309013
Share on other sites

run the screamer pipe through a 2inch cat or something mountedunder the car.

this way the exhaust is let off through a cat (not illegal)

then go to your local exhaust shop (EPA approved or whatever) and get a db test done.

when they rev it to 4xxx RPM, the wastegate wont open, making it legal noise at the required RPM.

its only loud under full noise.

Think about it. :cheers:

Link to comment
https://www.sau.com.au/forums/topic/70955-screamer-pipes/#findComment-1309942
Share on other sites

run the screamer pipe through a 2inch cat or something mountedunder the car.

this way the exhaust is let off through a cat (not illegal)

then go to your local exhaust shop (EPA approved or whatever) and get a db test done.

when they rev it to 4xxx RPM, the wastegate wont open, making it legal noise at the required RPM.

its only loud under full noise.

Think about it. :P

Hey this is a clever idea :cheers:

I agree, this would work as you really only need a cat on the screamer pipe for legal reason's but mufflers and such are for noise reduction. The wastegate will not open at 4000rpm with no load so this will pass a db test.

You get the best of both world here, legal and a screameeeerrrr :wassup:

Link to comment
https://www.sau.com.au/forums/topic/70955-screamer-pipes/#findComment-1310191
Share on other sites

Hey this is a clever idea  :cheers:  

I agree, this would work as you really only need a cat on the screamer pipe for legal reason's but mufflers and such are for noise reduction. The wastegate will not open at 4000rpm with no load so this will pass a db test.

You get the best of both world here, legal and a screameeeerrrr  :wassup:

However, even though you pass the noise test you may not be legal still unless you adhere to the standards regarding how far back and where you are allowed to vent exhaust gases. In the ACT i am prett sure you are *only* allowed to vent exhaust gasses out behind the rear bumper and are not allowed to vent at an angle. Just something to think about.

Link to comment
https://www.sau.com.au/forums/topic/70955-screamer-pipes/#findComment-1310298
Share on other sites

Hey this is a clever idea  :cheers:  

I agree, this would work as you really only need a cat on the screamer pipe for legal reason's but mufflers and such are for noise reduction. The wastegate will not open at 4000rpm with no load so this will pass a db test.

You get the best of both world here, legal and a screameeeerrrr  :wassup:

not really, see thats extra piping, which in turn is extra weight.

when you could simply plumb it in just before your normals CAT

and you have no issues what so ever, and you save piping/weight and space

Link to comment
https://www.sau.com.au/forums/topic/70955-screamer-pipes/#findComment-1310392
Share on other sites

However, even though you pass the noise test you may not be legal still unless you adhere to the standards regarding how far back and where you are allowed to vent exhaust gases.  In the ACT i am prett sure you are *only* allowed to vent exhaust gasses out behind the rear bumper and are not allowed to vent at an angle.  Just something to think about.

In Vic I belive it's something along the lines of:

Behind the last openable window and on the drivers side

Link to comment
https://www.sau.com.au/forums/topic/70955-screamer-pipes/#findComment-1310410
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Power steering is probably because someone has nuked the HICAS CU and you no longer have the variable power asist doing what it is supposed to. How much boost are you running? You are aware that any more than 10 psi on the stock ECU is just asking for it to go to full R&R (that's Rich & Retard, which is effectively Retarded and Retarded!) which kills all the power. Depending on the exact conditions, it can just be runnign on the fat and stupid end of the maps, then the conditions change, you make a little more boost and the ECU goes into panic.
    • @BuiltNotBought Just as GTSboy said.   If you want driveabilty and more low down torque..keep the stock runners. They are VERY good from a factory. I have them too on my RB25DET NEO and as a GTSboy i have fmic but with stock piping route(i have Blitz intercooler) Iam making around 320 BHP and the car pulls "hard" from like 2,5k all the way to 7k. I have it dyno tuned to mimic N/A power curve and making little less max torque due to the smallbox tranny. But driveability is very great. I had 350Nm below 3k so car feels very quick.   EDIT:  Not my channel but i saw this and i know that is what i want (and i have exactly this)  
    • Looking to sort out a couple of issues on my skyline  It recently was rebuilt, however rebuilder long story short did not give two flying effs about the work he did. So moving forward it's running but I have two persistent issues 1) it has a misfire / lag type of issue (was at higher RPMs but I had a dead piggy back ecu removed which improved it) now it's not as bad but still does it at random, I thought it may have been a boost issue I'm running an older turbosmart dual stage controller, turbosmart told me to try running off gate pressure however it still has a lag at random times. It has New MAF, maf plug, coil packs, sparks, CP harness.. injectors tested and cleaned. Factory ECU. 2) Power steering issue. It is tight as anything. Flushed power steering, rebuilt my pump because the bearing was shot. Flushed again still tight (mainly when parking and going slow into my driveway etc)  No kinks in hard lines, replaced the lines I could see had cracks. Still tough to steer.  I was told to shim a coin and place into the solenoid plug? Is there anything else. My steering angle sensor also has a issue. It's a used one I replaced, does it need to be calibrated? I feel like I've tried everything and this car is my voodoo doll.   
    • Holy shit... wow!!! I totally missed this
    • One main filter. Each tank has a prefilter to keep rocks and small children out, then the big main filter that also does water separation. Clogged the first one so bad it was like a rev limiter at 3200rpm. Literally just like dropping the throttle off and maintaining rpm!
×
×
  • Create New...