Jump to content
SAU Community

Recommended Posts

Hi Guys,

hopefully someone can answer this fairly quickly,

i need to replace my rear speakers, and i was wondering how to get the grills off, i am hoping you don't have to remove the whole rear parcel shelf.. how does it remove anyway, assuming the rear seats are already removed, does it just clip on?

thanks guys

Link to comment
https://www.sau.com.au/forums/topic/7188-removing-rear-speaker-grills/
Share on other sites

I've got some pics I took when I took out my parcel shelf in my gtst - same as a gtr?

I got cranky trying to get the parcel shelf out and snaped both ends. There are 2 white clips you can see in the above photo that you need to deal with to remove the shelf.

Be careful on each edge of the parcel shelf (I think you have to push down at the edges to do it properly - I just pulled and ripped it out).

Mark

Hi Y0880,

Since the last photo was useful I edited one of the ones I took of the rear seat with parcel shelf removed . You will notice there is yellow where the teeth Akeenan mentioned are - from memory it looks like a tiny single fin from a surf board. This goes into the parcel shelf where I have circled with yellow - if you look hard you'll notice that the slot on mine has been ripped.

The two red circles are where the two white clip type things are. After removing the back seat I got my fingers under the parcel shelf near the middle and pulled it up which worked... maybe there is a better way?

good luck with it, hope it helps you and other people.

Mark

  • 2 weeks later...

Can you repost those pix, they've been removed from the server...

Wouldn't mind getting a look as sometime I'll have to remove the same to install some new speakers in..don't want to stuff the parcel shelf and have to build a new one (time/money) :P

Well,

Pulled the parcel shelf out finally today, and it was a little different to your pics, basically there where a few metal wire clips holding it at the rear (near the bottom of the glass), two bolts for a child restraint anchor point, and two fins from the plastic cover on the C pillar that went into the rear parcel shelf..

Got most of the shelf off, but couldn't for the life of me get the right corner out.. finally after a bit of tugging it came out, but i managed to rip the thin bit of parcel shelf off at the back behind the breather grills.. so have to work out a good way to stick them back on..

So's life :P

Ok, i'll put those pics back up now.

Those metal clips near at the rear didn't seem to do anything so when putting it back i didnt bother with them. I guess the guys that did the compliance work with the child restraints didn't bother with them either.

You ripped the parcel shelf like I did with those fins :) Its a bastard of a thing especially with this hot weather + the frustration that builds up over something as trivial as this.

Good luck with your parcel shelf predator666, see if you can get the it off without ripping it.

Mark

yeah, it doesn't look too bad though, didn't rip the carpet completely off so hopefully when i add some sound deadener it will hold things together..

I know what you mean about frustration.. it isn't as bad as other cars i have worked on (Holdens are probably the worse so far), but hours in cramped confines never helps :)

i will post up some pics when i get it back all together, probably a few days away yet though..

Good luck with your parcel shelf predator666, see if you can get the it off without ripping it.

hehehe...well i will give it a good try! But I need some rears to fit in first before I get the willpower up to try and take it out... much as it sucks, just going stockie speakers for now through my new face unit 'till i can get some nice ones. Thinking alpine.

I put some pioneer speakers in for the rear. I also had to remove the stock rear speaker mounts and make my own because the speaker screw holes didn't match up to the aftermarket speaker.

You will also have to do something similar to me out of MDF if you want your future alpine or whatever speakers to fit.

Happy New Year.

Mark

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...