Jump to content
SAU Community

Recommended Posts

for the resistor pack you can use 6 10W 10 ohm resistors from Jaycar/Dick Smith. Will cost about $6 but then just package them nicely in a box.

Your mom fixes cars????

:) oh sorry, "he"

with the resistors you already have Roy's detail on fitting them? this is the same but just solder the power wire into the 6 resistors at one end (twist them together) then run the other ends to each injector in place of the power wires they have. The switching is done in the ecu to earth the injector and make go bang.......

for the resistor pack you can use 6 10W 10 ohm resistors from Jaycar/Dick Smith. Will cost about $6 but then just package them nicely in a box.

does anyone know the exact ohm and W resistors to use. i've read on these forums so many different things. 8.5 ohms, 7 ohm, 10W, 17W. i don't want to wire the wrong sized ones in and short something out.

  • 4 weeks later...
  • 3 weeks later...
appaerently, no-one on here knows. so i bought some 6.8ohm resistors. i'll let you know how they go real soon

Hey SluggerS13

Did you end up putting them in and did you take any pics of finished result?

I bought the 10ohm, 10Watt as found another site which a couple of people claimed they used them.

I once found a page which someone posted pics and full instructions of Jarcar resistors installed but have been searching for weeks and can not find it.

Spewing.

thanks.

There was a page in here, I am sure it was the wanted section in response to somebody looking for the factory item, and it was explained how to make it with fairly clear instructions.. but I can't find it in here anymore either :)

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah I've had too many issues with knock off's on the BMW's. I don't want to do a job twice or more because the parts are shit.
    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
×
×
  • Create New...