Jump to content
SAU Community

Recommended Posts

I've got the following forsale.

Oil filter relocation kit $100 (suit RB engines) -SOLD

Black R32 GTR boot minus spoiler $90 - SOLD

R32 GTR Stock front pipes $50

R32 GTR Stock dump pipes $20

R32 GTR Stock front sway bar $30

Brand new Field One Connector for RB26 ECU $150 (its a wiring harness that goes between the ECU so you dont have to cut up the original harness to install things like a boost controller etc..something like the attached picture)

pm me for more details

Cheers

Could I get a little more info on the Field One connector? Do they have a website? Where exactly does it tap in to the loom (at the ECU I take it from your description)? Some close up shots would be great.

:P

Lucien.

Ronin 09

I dont mind sending the boot to Melb, as long as you pay for freight

lwells

I'll get a digital camera and take a pic. The way you connect it is as follows. The loom connects to the field one connector then the field one connector to the ecu, its a 10minute job.

cheers

Ronin, I will bow out and let you have it. I only wanted it mainly because it was cheap, and because my boot has a couple of holes in it from a wing that I have now removed. I will just weld them up when I can be farked. enjoy the boot :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Version 1 aluminium airbox is.......not acceptable No pics as I "didn't like the look.....alot" Even after all my "CAD", and measurements, the leg near the fusebox just didn't sit right as it ended up about 10mm long and made the angle of the dangle look wrong, the height was a little short as well, meh, I wasn't that confident that Version 1 was going to be an instant winner I might give Version 2 another go, there's plenty of aluminium at work, but, after having in on and off a few times, and laying in the old OEM airbox without the new pod filter and MAF, there may be an option to modify the OEM air box and still use the Autoexe front cover and filter.... maybe This >  Needs to fit in here, but using the panel, and not the pod, the MAF will need to fit in the airbox though> I'm thinking as the old OEM box and Autoexe cover that is sitting in the shed is just sitting around doing nothing, and they are relatively abundant and cheap to replace if I mess it up and need another, it may well fit with some modifications to how the Autoexe brackets mounts to the rad support, and some dremiling to move it get in there, should give me some more room for activities, as I don't want to move the MAF and affect the tune Sealing the hole it requires to stick it in the air box is simple, a tight fit and some pinch weld will seal it up tight  I am calling this a later problem though
    • and it ends up being already priced in as though you're just on 91RON without any ethanol. Car will lose a bit of economy as the short and long term fuel trims bring down the AFR back to stoich or whatever it is for cruise/idle for the engine.  
    • Oh, you are right. But, in Australia E10 is based on 91RON fuel and ends up being 94RON. Hence it being the cheaper option for economy cars. The more performance oriented cars go for the 98RON fuel that has no ethanol mixed in. The only step up we have left then at some petrol stations is E85.
    • There is a warning that "this thread is super old" but they ignore that anyway...
    • With 10% Ethanol, we're talking 2-3% fuel consumption difference. The emissions reductions and octane boost in my opinion far outweigh this almost non existent loss.    My tanks sitting at 80%. Luckily that should go down fast as I'm on vacation again for the next two weeks. 
×
×
  • Create New...