Jump to content
SAU Community

Brand New Volks


Recommended Posts

Hi Guys,

Im looking at getting some brand new Volk GT-C or Gram 57pro for my 32 GTR. Now what is ALL the required infomation i need.

Am i right in assuming that 18x10 is the best setup for a GTR ? The rims must be the same size and offset for attessa requirements ?

Cheers for any info.

Link to comment
Share on other sites

I bought the Volk TE37 for my GTR R33. The spec you need are:

114.3 PCD, 9.5" wide (these will fit 265, 275 very nicely) & @+19 offset. a lower offset will mean a deeper dish. I got the lowest offset. Here is a picture of one with 19 x 9.5 with +19 offset.

Link to comment
Share on other sites

Hi I got Blitz 18x10 with and offset of +22 and they stick out just a little so the camber had to be adjusted a bit. If you can get an offset of +25 then that would be perfect. Else 18x9.5 would be just right with an offset of +19 or so.

cheers

Link to comment
Share on other sites

  • 2 weeks later...
I bought the Volk TE37 for my GTR R33. The spec you need are:

114.3 PCD, 9.5" wide (these will fit 265, 275 very nicely) & @+19 offset. a lower offset will mean a deeper dish. I got the lowest offset. Here is a picture of one with 19 x 9.5 with +19 offset.

omg. that thing is hot. :love::whackit:

d

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Took a little trip  went to nismo hoping the get my fuel tank hoses and unfortunately they told me they didn’t have stock luckily I was able to go to a Nissan parts store and they were able to order them in for me  then can home and cleaned the tank with some degreaser and fitted the new hoses before putting it back in the car 
    • 100% I’ll hack into the 33. Strap a turbo onto the RB25DE and/or put the 25 head on a 30 block. 33 passed in cos the reserve was too high. I’ll try lowballing it again and negotiate. Aim is to have it landed and on the road for under 15k, then spend the same amount on top in mods.
    • It's generally best practise to run 1x run without VCT enabled, then 1x run enabled till redline. Overlay the two torque graphs and you'll find the desired RPM to turn off VCT. Sometimes, it might be even worthwhile turning off VCT earlier control torque/cylinder pressure and using VCT purely to spool the turbo.
    • They sell them in Malaysia for about $4
    • First time I ever have issues with Amazon, but my wife often tells me to keep an eye out for fakes. It finally got me. I wrapped up the conversation with Gates. The gentlemen I was talking to seemed to hate his job but the response time on their technical support is outstanding. He stated that the hose is marked with some variation of "SAE J30R10" but that if you only purchase a 1 foot length like I did, it is possible to get a cut between markings and have a blank hose. To no ones surprise, he stated the swelling and "gummyness" isn't normal and to replace/buy from somewhere else (He mentioned NAPA). I'll toss a small end of the new one in gas for a few days before pulling the hanger out again, just to be safe.  Hose should arrive Monday. For those running multiple pump in tank hangers, you know the joys of getting them out and back in. I'm surprised I haven't destroyed my level float yet.  Lastly once I wrap all of this up, I'm planning on hitting the dyno again in 2 weeks while I'm on vacation. I realized recently that my VCT is set to turn off at 5000RPM. I'm surprised it wasn't increased while I was on the dyno last. I'm expecting I can increase it to ~6500RPM, if not more. Should hopefully get another 15-20kw out of it. I also want him to revisit my knock thresholds. I'm occasionally getting false knock around 3000rpm. 
×
×
  • Create New...