Jump to content
SAU Community

Recommended Posts

  • Replies 76
  • Created
  • Last Reply

Top Posters In This Topic

No grille or bonnet.

No seats

Shit looking wheels and only 3 of them 17x8.5's want $100 for 3

Got the boot and 2 side badges make an offer

ABS unit was removed yesterday, looks brand new. will sell for $200 plus freight. Its fairly heavy so freight would probably be $20 or something I can price if your interested.

I've got both front guards but condition is questionable LHS has some damage on the top easily repairable and RHS is a bit twisted, could be repaired if you were really keen. I've got $120 on the pair, but don't really want to freight them. Might have an adelaide guy looking at them today anyway.

Got the Intercooler, but have a guy coming up this arvo for a look. I told him $800 including every bit of 3 inch plumbing that GTR's have. Even I think this is expensive, but there a wanted item. I'll see how I go. dont really want to ship it anywhere incase it gets damaged, but you can pick up if in adelaide an interested at this price.

The intercooler will be $750 next week and $700 the weekafter that. probably even $650 the week after that

Pickup only on this item

what condition is the dashboard in?

i DONT need any of the guages, centre console, vents ect ect ect. just need the dash as mine has a hole cut in it.

if its in good condition, no cracks holes ect, how much do think you'd be after?

Sold the rear sway bar already, not sure if its different to GTST or not. Got $60 for it.

No bonnet

Clutch is organic with a tricky looking pressure plate, still good condition but nothing for big HP.

Everyone seems to need that left air vent, I should be asking $100 for it. lucky I'm not. Someone call me and bring over some money.....

I have the centre vents. they'll be cheap make your offer.

I'm heading into the shed for 4 or 5 hours to keep stripping this car, so if you want info, ring me 0421119952.

That way I can be looking at the parts when I'm talking to you.

This is my girlfriends phone, so please dont ring during work hours 8-6 mon to fri, but feel free to call any other time. IF you wake me up cos its late, thats OK, but you might find that the prices are more expensive :rofl:

anyone need a complete uncut wiring loom?? Just spent 3 hours removing it, a real bitch to do without cutting any wires. Note the part of the loom that runs the engine has gone with the engine, but I have the rest of it. If I charged $10 for each time I hurt myself removing it I'd be a rich man.

Back in from the shed for tea...

I've sold the front bar.

I have the A/C unit which bits exactly do you need?

I have excellent carpet (freight to melbourne would be a pain... $50 pick up or you to organise freight.

I have the gear knob (sort of) my mate stole it and put it on his 31, but hes coming back to swap it for a Razo knob, so I'll have it next week price negotiable make an offer.

I have both turbos in excellent cond no shaft play and want $600 for the pair.

Back to the shed to pull the diff out....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
    • The video for the servicing and fuel filter change can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44 One of the main jobs I wanted to do before the car officially went on the road, was to remove the awful looking blue silicone hoses. There's nothing wrong with having coloured silicone hoses, but I realise as I'm getting older I prefer monotone engine bays with a splash of colour on the engine cover(s). I cover this in a lot more detail in the Youtube video, so unfortunately there's limited photos of the process. The intercooler, upper radiator, boost vacuum and upper breather hoses were all changed to black silicone with mikalor clamps. The only blue left is a blanking cap at the back of the inlet manifold and the GReddy pulleys (which will be replaced for stock when the cambelt gets replaced) While the intercooler pipes were off I gave them a quick clean/polish too A before photo I do have a replacement air filter on its way. Fuse box covers were painted blue, they're now satin black Another job on the list while the bumper was off, is to add some mesh https://live.staticflickr.com/65535/54737966256_99b28bfa30_c.jpg[/img] I was hoping to use some thin wire to secure it, but it seems I've misplaced it and the wire I had was too thick to twist easily. I ended up using cable ties for the time being https://live.staticflickr.com/65535/54737131882_c2b7989dcc_c.jpg[/img] Was pleasant to see this https://live.staticflickr.com/65535/54737131627_8b2aab13b3_c.jpg[/img] The last thing to do was to fix the front grill and re-mesh that to match but I ran out of time The Youtube video can be seen here: https://www.youtube.com/watch?v=R4FsF6tgizE&t=23s
    • Hi all,I already introduced myself in the Victoria section, but only saw this section now lol XD New to forums and new to skylines. Hoping to buy my new skyline within October
×
×
  • Create New...