Jump to content
SAU Community

Recommended Posts

xenon globes i think have this like graphite type rod running down the lengh of the globe, not connected to the glass bit, but running parrelel with it...

That's what the dud bulb I have is. Definitely xenon as it is a Panasonic D2S-35W. Philips ones are about US$75 replacement, the only thing annoying about that is shipping time.

When my HID globe went i rang nissan and was quoted $350.

I ended up getting a globe from nissan which was out of a new renault for $200.

Xenon Light Type D2R

#472267.

Phillips 85v 35w

It needed a clip cut off but works fine

Also does a R33 GTR series 3 high beams and low beams come on at the same time when the high beams are turned on ?

Xenon bulbs are good now thanks to ferni. Cheers Andrew.

Problems ( :) ):

1. I am missing parkers altogether! Who the hell removes them?! So I need bulbs and the holders to clip into the factory power lines. Does anyone know what holders are the same? Do any other Nissan models, for example, have the same holders? Need them for both sides so I don't even have something to go on.

2. Low voltage power for driver's side head lamp is not getting to the relay at all. It is definitely that as running high voltage straight through flickered the low beams. I have checked fuses in the engine bay and under the dash (only what appeared to be 'battery' ones - 7 of them). Does anyone know where I can get a fuse box layout diagram in english? Or is there any other fuses at all?

That's what the dud bulb I have is. Definitely xenon as it is a Panasonic D2S-35W. Philips ones are about US$75 replacement, the only thing annoying about that is shipping time.

The Us 75/pair delivered? How about warranty?

The Us 75/pair delivered? How about warranty?

Not sure. I found them on a website, not sure if that includes delivery. Or warranty. Looks up the bulb type in google and you'll come up with something.

Anyone have any ideas for my problems...? :)

Not sure. I found them on a website, not sure if that includes delivery. Or warranty. Looks up the bulb type in google and you'll come up with something.

Anyone have any ideas for my problems...? :)

just checked on a few site the pricing are mostly /side excludes delivery kinda of expensive and only a short time warranty provided.

Hey mate, have a look in this PDF for fuse translations...

http://gtr.ferni.net/misc/skylinebook.pdf

There are 3 fuse boxes i think, one under bonnet, one in cabin (drivers side) and one in the boot.

Parker bulbs are easy to find/get... standard wedge ones.. as for the clip in stuff, hmmm i'll PM the guy i sold my old headlights to, he damaged his in an accident but chances are his clip in things are still ok, maybe he can sell them to you?

Edit: I sent him a PM, http://www.skylinesaustralia.com/forums/in...p?showuser=9963

I'll check the fuse box in the boot now I guess!

Interesting that the holders/clips are missing altogether, very stupid that they weren't at least returned to their spot without a bulb.

Thanks for all your help with this Andrew. Much appreciated!

Are R34 Xenon bulbs the same as the R33 GTR bulbs? If so, I have 4 that I would be willing to part with. Not 100% sure if they all work as I don't have any Xenons to test them on, but I AM certain that atleast 2 of them are perfect.

Anyone in Brisbane northside want to test them for me?

  • 3 weeks later...

Green? Mine are the same bulbs you have, and look half between the white xenon colour and standard halogen yellow colour.... maybe a bit more on the white side, but my old bulbs were definatly whiter... but i read they need some time to wear in to give that white colour, which is why most people change both at once if one blows.

  • 6 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...