Jump to content
SAU Community

Recommended Posts

Hi ppls

Ive been putting my car back together for a while now. Now that it is together, the damn thing wont start, we put new spark plugs in it last night and it doesnt seem to be getting any fuel, fuel pump is working but the injectors dont seem to be working at all. I need to check that i have an r32 gtst computer and not some random the fella i bought the car off picked up at the wreckers. So if anyone can help with a part number that would be greatly appreciated.

The codes written on the side of the ecu are MEC-R212 B 1X22 Those are on the front on a nissan tag. Also on the side is MEC-R212 B 06645

We pulled the spark plugs out and after trying numourous times to start it they were dry and had no signs of any fuel getting to them, also when we were trying to start the car and feeling the injectors you couldnt feel them pulsing whereas my mates car was very noticable, thats why we are guessing its the injectors.

Thanks guys.....Brett

yeah im pretty sure the lines are on the right way, we pulled the line off to make sure there was fuel being pumped through. wouldnt the injectors still be pulsing to try pump fuel into the engine even if there wasnt any fuel there? coz they definitely arnt doing anything.

One of the green relays down behind the ECU controls power to the injectors. Make sure that both relays (the other is for the coils) are switching on when you set the key to "ON".

Trace the fuel line from the FPR back towards the the fuel tank. If you run into the fuel filter, then the fuel lines are on the wrong way round. But that shouldn't stop the injectors pulsing.

While you had the plugs out, did you check that you had spark?

I have on old ECU, but its from a GTS4. The Nissan P/N is 23710 04U60 (It has MEC-116 A 9810 just above the "Hitachi" on the label)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...