Jump to content
SAU Community

Recommended Posts

Well the adjustable exhaust camshaft pulley arrived today, I ordered an Apexi one form Nengun originally, but they don't make them anymore. I had to settle for one of the new duralium HKS pulleys.......

HKS_Adj_Pulley_Small.jpg

I weighed it (just out of interest) at 350 grams, from memory a standard pulley weighs around 550 grams.

I already have the cambelt which is due for replacement.........

Cam_Belt_Small.jpg

So it's time to fit it up, more pictures and a how to do it guide will follow over the next few days. So watch this space

:) cheers ;)

Edited by Sydneykid
Link to comment
https://www.sau.com.au/forums/topic/73824-adj-camshaft-pulley-new-cam-belt/
Share on other sites

First job is to read the workshop manual, for those that don't have one I have attached the relevant drawings from the RB20/25/26 manual. They are all pretty much the same, I have just chosen the best diagram from each manual.

This is a picture of the crankshaft pulley, you need to make sure it is at TDC (Top Dead Centre on #1 or Zero Degrees), when you start, and when you finish.

RB26_Crank_Pulley_Orientation_at_TDC.jpg

This is a picture of the camshaft orientation, you need to make sure they are both at TDC, when you start, when you finish and at all times in between.

RB25_Camshaft_Orientation_at_TDC.jpg

If you don't want (need) to remove the cam covers, you can check the camshaft orientation by the location

of the knock pins, as per the following diagram;

RB26_Camshaft_Kock_Pins_at_TDC.jpg

The best way to check this is the camshaft pulleys, they have a dot on each pulley that should (has to) line up with the dots on the backing plate. Like this;

RB25_Cam_Pulley_Diagram.jpg

Take a look at the picture of the HKS exhaust camshaft pulley (in the previous post) and you can see the dot on the tooth just above the "EX" mark.

There is also an alignment dot on the cambelt pulley on the crankshaft, you need to make sure it is at TDC (Top Dead Centre on #1 or Zero Degrees), when you start, when you finish and at all times in between;

RB26_Cam_Pulley_Diagram.jpg

Nissan knows how important it is top make sure you have the crankshaft and camshaft timing aligned. That's why there are all of these dots and markers to make sure you align them when you put it back together. Use them, they will save you a lot of heartache if you get it wrong.

Most of these parts I will have to remove to change the timing belt and replace the camshaft pulley;

RB26_Cam_Belt_Replacement.jpg

Note the torque wrench settings for each nut and bolt, it is important not to overtighten them or leave them loose.

The next post will contain some digital pictures of the RB25DET in the Stagea and the parts that need to be removed to get at the front of the engine. So that I can remove the crank pulley and the cambelt covers. Taking pictures as I go will take longer than I could do it without stopping, but I will have a nice record of what to do. As I get a lot of questions from guys who have done or would like to do their own cambelt service or fit an adjustable camshaft pulley/s.

More to come over the weekend.:D

Edited by Sydneykid
  • Like 2

Next step, mark the CAS so I can put it back in the standard position;

CAS_Std_Position_Small.jpg

I always mark 2 of the 3 bolt positions, just in case 1 gets rubbed off.

Now check the standard ignition timing with the timing light. Connect the timing light sensor around the black with yellow stripe wire (nice loop Nissan);

Timing_Light_Connection.jpg

Confirm that the ignition timing is set at the usual (factory) 15 degrees;

Timing_Check_Small.jpg

Trick photography huh?

Next post we will start removing the parts that are in the way

:) cheers :D

Edited by Sydneykid

Just rude of you SK to hide this in the Stag section :P

Champion effort and great trick photography :D

I'll be sure to just direct the team here instead of having to explain the procedure for cam belt/pully changes another time.

also, do you have advise on how tight we should make the belt? i think i over tightened my belt and it made a whiing noise when i started it up.

Ill replace the pulleys to make sure, but i just wanted to see if there was a way of checking to see hwo tight it is. i know theres a tool that can check for you.

steve

also, do you have advise on how tight we should make the belt? i think i over tightened my belt and it made a whiing noise when i started it up.

Ill replace the pulleys to make sure, but i just wanted to see if there was a way of checking to see hwo tight it is. i know theres a tool that can check for you.

steve

Personally I set the belt tension so that I can move it 5mm in and out (ie; 10 mm total movement) using one finger. You should not able to play it like a violin because it is so tight. Measurement is done between the inlet pulley and the tensioner. You should have the same amount of movement from the exhaust camshaft pulley to the idler pulley.;)

When I check the Stagea belt tension I will post up the pictures.

  • 2 weeks later...

I will be adding some more words over the next couple of days, so watch this space....

When you take the top cover off, this is what you should see when the crankshaft pulley is at TDC. Note the alignment of the dots. I have added the red dots in PhotoStudio so they stand out in the pictures.

Both_Pulleys_Alignment_Marks_Small.jpg

This is the exhaust camshaft pulley, note how the dot on the pulley lines up with the dot on the rear cover plate;

Std_Exhaust_Pulley_Alignment_Small.jpg

This is the cheap harmonic balance puller I used, ~$25 from SupaCheap;

Balancer_Puller_Set_Small.jpg

The genuine Nissan cambelt has these markings on it, note the arrows indicating front and the dotted and solid lines that align with the dots on the camshaft pulleys and the dots on the rear cover. This makes it very easy to get the camshaft timing correct, which is very important, obviously.

Cam_Belt_Markings_Small.jpg

This is after the harmonic balancer was removed, showing how the puller is located;

Balancer_Pulley_Small.jpg

The HKS Pulley is on and its dot aligned wth the dot on the rear cover;

HKS_Pulley_Aligned_Small.jpg

Note the position of the CAS spigot in the camshaft, with the flat facing up. This makes it easy to align the CAS when refitting it. I set the exhaust camshaft timing at zero, I will adjust it on the dyno the week after next.

Note the dots on the crankshaft cambelt pulley aligned with the one on the oil pump cover. This indicates TDC, which is usefull when you have the harmonic balancer off;

Crank_Pulley_Marking_Small.jpg

I have added the yelllow dots in PhotoStudio, so they stand out in the pictures.

The finished product,

Cam_Belt_Finished_Small.jpg

Note how the CAS is slightly rotated clockwise from its original position. I adjusted it using the timing light to ensure that the ignition timing was back at its original 15 degrees advanced. This change in orientation occurs because the new cambelt is shorter than the old one, it had obviously stretched a little over its 105,000 k life.

Don't forget to fill in the cambelt changed sticker and whack it on the top cover so you know when it needs changing next.

The tools used in the this job were;

5mm allen key socket

10/11/12/14/27mm sockets

10/12/14/17/19mm rachet ring spanners

3/8" socket drive with short & long extensions

1/4" socket drive with short & long extensions

1/2" tension wrench

1/2" rattle gun (essential for removing the harmonic balancer in an auto, maybe you could get away with using the 1/2" tension wrench in an manual)

Several flat and Philips screw drivers

Harmonic balancer puller (essential, don't even think about trying it without one)

Timing light (essential, don't even think about trying it without one)

oil catch tray

rags

Things to remember;

Buy some coolant, as you will loose most of it when you remove the radiator

Buy some auto trans fluid, as you will loose some when you disconnect the cooler hoses from the radiator

Check the condition of the waterpump, make sure it spins freely and has no sign of leaks from the front seal. At the same time check the tensioner and idler pulleys, they should spin freely with no tight spots or noise.

Bleed the air out of the engine, while filling up the radiator, this is the fitting on the inlet manifold to enable that;

Cam_Belt_Air_Bleed_Small.jpg

Hope that helps someone else do there own adjustable camshaft pulley upgrade or cambelt service.

:cheers: cheers :P

Edited by Sydneykid

A good tip....

When using the balancer puller, you need to find 2 bolts that will screw in to the threads provided. After realising all the ones in the kit you got dont fit and that you dont have the right bolts anywhere, look in the pile of bolts you've undone so far.

The top 2 bolts that held the timing cover on are perfect. Just find 2 washers and your set to go.

If I'm not mistaken, these are the bolts that SK has used as shown in the above picture.

A good tip....

When using the balancer puller, you need to find 2 bolts that will screw in to the threads provided. After realising all the ones in the kit you got dont fit and that you dont have the right bolts anywhere, look in the pile of bolts you've undone so far.

The top 2 bolts that held the timing cover on are perfect. Just find 2 washers and your set to go.

If I'm not mistaken, these are the bolts that SK has used as shown in the above picture.

You are not mistaken:cheers:

SydneyKid, once again, you've outdone yourself.  Excellent, excellent, excellent.

Lucien.

Thanks Lucien, I have just about finished and updated the tools used etc, I think :confused:

To all, please let me know if I haven't covered something that you might need to know:cheers:

Hi SK,

Very interesting and useful guide!

Are you planning to adjust the exhaust cam timing and run some dyno tests?

When I fitted my WOLF ECU, I had to wire in some mods to activate the intake cam solenoid. I left it standard until about 2000rpm, activated it (advanced the cam), then dropped it out at about 6000rpm. I did dyno runs and an advanced intake cam helps power at mid rpm, but I was unable to detect any improvement above 6000rpm advanced or standard. This was with the standard turbo. I have since high flowed the turbo but not re checked the intake cam vs power.

Any thoughts?

Rob

Hi SK,

Very interesting and useful guide!

Are you planning to adjust the exhaust cam timing and run some dyno tests?

When I fitted my WOLF ECU, I had to wire in some mods to activate the intake cam solenoid. I left it standard until about 2000rpm, activated it (advanced the cam), then dropped it out at about 6000rpm. I did dyno runs and an advanced intake cam helps power at mid rpm, but I was unable to detect any improvement above 6000rpm advanced or standard. This was with the standard turbo. I have since high flowed the turbo but not re checked the intake cam vs power.

Any thoughts?

Rob

Hi Rob, the way we do it is to do 2 power runs on the dyno, one with the VVT on and one with the VVT off. We then overlay the 2 graphs, that tells us exactly where the change over points should be. Even on fairly modified RB25DET's (305 rwkw) with Tomei Poncams, the standard change over points are pretty much spot on.:P

Hi SK,

Whats the total cost for this mod all up?

Genuine cam belt = ~$90

HKS Pulley from Nengun = ~$185

Castrol Radiator concentrate fill = ~$9

Castrol Auto Trans fluid top up = ~$10

One day of my time = priceless

On the same day I did an engine oil change, filter change, radiator flush and a full cooling system refill. Plus I bought a new harmonic balancer puller for ~$25, but I can use that again obviously.

:P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The car/ECU will have all the sensor that it needs and expect to have. I think i do not have to explain to you how the Link is way better specialy if you have swapped engine   I just do not want to deal with any "problems" cuz i have only Nistune which i learned is not that great and in my case cant even deal with that speed problem (Link can) And of course it will be way more easier to tune and diagnose and safe. And for the ECU/speed problem...i dont know.
    • Per Mark Roberts of Sonictune: Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • Per Mark Roberts of Sonictune:     Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • The fancy pants red shock tower brace is finally incoming from MX5 Mania, getting it shipped from 'Merica has been a long and problematic process, and GWR, the 'Merican supplier will not ship directly to consumers outside of the US, Mania basically had to order a heap of them, the colour choice was silver, or red, and we all know anything red adds 5 killerwasps of dynotorques..... Whilst it does fit over a 2.5, and I've seen a few photos and videos of it being installed and fitting, google also says it might get real close to the FAB9 intake front runner, people in the US says it does fit with the FAB9 intake, except for one person who said it slightly touched.......so there is that.....LOL..... As it seems that I am the first in AU to have this combination of parts there's no local knowledge about fitment, so I'm just a willing guinea pig in this endeavour, I'll cross my fingers and toes and hope for the best In other news, I ordered stuff from China  on the same day I ordered the 23° silicone bend from Victoria, the stuff from China arrived a day ago, the 23° silicone bend is still travelling around Australia thanks to Australia Post, and "may" be here next week
    • Very good news...I contacted Racebox about it last night. My car is a 2016 so remains to be seen if it is compatible, requires a TCU swap, or is impossible.
×
×
  • Create New...