Jump to content
SAU Community

Recommended Posts

I wouldn't have thought that three screws would be sufficient enough to hold the gear in place. not due to the strength of the bolts but because the force is a lateral one. Being ally i would tend to think that after time the bolts might eat into the material, causing them to loosen.

Having said that i could be totally wrong, but personally, I like................

OVER KILL!!!!!!

The force on the bolts is not really a shear force. The bolts dont transfer the majority of the force, they clamp the 2 halves of the gear together and the friction between the 2 mating surfaces provides the drive. the load of the bolts is mostly tensile.

If you're worried about 3 6mm bolts providing enough clamping to drive the cam, never look at an OS-giken twin plate clutch, they use 6 or 8 6mm bolts to hold the pressure plate on and these can transmit 600Nm of torque.

On the "series 1" design of the HKS cam gears, the metal used for the teeth the belt sits on is too soft, and I have seen a few which have worn away pretty quickly (under 15,000kms). You can identify the series 1 design as having the purple center and blue outer edges.

The "series 2" design is made out of the same metals as Tomei's cam gears, and I havnt heard or seen any problems with the Tomei ones.

I know this sounds dumb, but how does a rubber belt wear out an alloy pulley?

It's not the belt that wears the pulley, it's the dirt and dust that gets squeezed through between the belt and gear. The dirt can embed in the belt and continually wear away at the pulley, similar to sandpaper. It's a good reason to run a belt cover.

It's not the belt that wears the pulley, it's the dirt and dust that gets squeezed through between the belt and gear. The dirt can embed in the belt and continually wear away at the pulley, similar to sandpaper. It's a good reason to run a belt cover.

Completely agree, plus over tightening (the belt tension), I have seen some that you could play like a violin.:)

Im another for seeing a few pairs of the earlier hks gears wearing,  apprantly teh new generation ones have a harder gear material,

I have seen 2, one had the belt so tight it's a wonder it didn't run the front camshaft bearings. It also had loose pulley bolts. So the pulleys were floppy around. Any wonder it wore the teeth. The second one I was called in to have a look at. It had no top cover and they had reused the old belt on the new pulleys. The bottom cover had so much dirt in it, when they took it off, I could have grown roses.

I couldn't blame the pulleys in either case.:D

ive the trust pullies on my rb20 and they seem to be quite a piece of kit.

too bad the car hasnt moved out of my driveway in awhile, so ive no idea on the wear patterns.

i do run the covers all the time for fear of a stray stone wrecking the engine.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...