Jump to content
SAU Community

Blow of Valve setup GTR

shaqrx3

By shaqrx3,
in Engines & Forced Induction

 Share

Recommended Posts

DJ984 Mentor

DJ984

Posted
Posted

but they sit open at idle (sucking in air AFTER the afm) so you can't vent them directly to atmosphere (learnt that the hard way)... they suck air in at idle causing stalling and rough as guts idle.

mine had an adapter kit put on them from the previous owner in japan. they vent to atmo and cant suck in any air :cheers:

TTT Grand Master

TTT

Posted
Posted

so you just wanted sound?

anyway,

shaqrx3 - factory bovs are probably the best setup you will get.

but if you must upgrade and want sound, the single greddy type R is fine. it is huge and it will flow more than you will ever make..

Let me know when you want to sell your stock ones.

MELV Experienced

MELV

Posted
Posted
but they sit open at idle (sucking in air AFTER the afm) so you can't vent them directly to atmosphere (learnt that the hard way)... they suck air in at idle causing stalling and rough as guts idle.

mine had an adapter kit put on them from the previous owner in japan. they vent to atmo and cant suck in any air ;)

yes they sit open at idle, which makes tunning a hell of alot easyer.

ask any one that tunes gtrs with AFM's. if you have bigger than stock turbos or BB turbos its hard to get the idle right with an aftermarked BOV.

i had that problem when i got the new turbos on mine, they couldnt get the idle right, because the BB turbos are still spinning damm quick after a bit of wide open throttle.

i also see it as helping the turbos as well, the plumb back system flows air after the intercooler back into the intake. so its breathing in cooler air :)

just my 2c anyway.

lwells Grand Master

lwells

Posted
Posted
anyone know where i can get stockies? ive got blitz one and theyre huge...but then again the BOVs are placed where most cops wouldn't look

They pop up every now and then when rice.. err.. people replace the stockers with aftermarket ones. Just keep an eye on the forsale section.

Lucien.

R31Nismoid Grand Master

R31Nismoid

Posted
Posted
They pop up every now and then when rice.. err.. people replace the stockers with aftermarket ones.  Just keep an eye on the forsale section.

Lucien.

yer, the for sale forum has then come by often enough for a few people every month or two etc.

But most people keep them i think as they know they are arite

lwells Grand Master

lwells

Posted
Posted
yer, the for sale forum has then come by often enough for a few people every month or two etc.

But most people keep them i think as they know they are arite

True, but given the prices on NS (as low as $150 for a "hybrid" copy FMIC) I doubt there is going to be many used ones much lower on here :D

LW.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      R33 Fuel Pump & Brakes after alarm swap

      By MBS206 · Posted

      Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • GTSBoy
      After market rear camber arm adjustment

      By GTSBoy · Posted

      Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Jarsky
      R33 Fuel Pump & Brakes after alarm swap

      By Jarsky · Posted

      Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...