Jump to content
SAU Community

Recommended Posts

lucien it should be much higher than that. when stone cold in the morning it should be up around 8 at idle, once warm should be above 2 at idle and driving at 3000rpm should be above 4. that is for a fairly fresh motor with a healthy oil pump etc. when giving it a 'boot' (talking 5000rpm+) it should get to around 6.

don't stress too much over it. my last car had much lower oil pressure than this one and it never had any major problems.

what is it when stone cold? mine is always above 6 when cold.

It's to be expected on an old motor i guess. things just wear. i am just lucky that i have a rebuilt donkey.

I'm not stressed, just annoyed. I've had about six hours use out of my car since getting it back -- that's after about 7 weeks off the road -- and now there is the possibility of another problem. I'd kill for, oh, say a month of hassle free motoring.

Re: cold start pressure, I didn't notice and I haven't had time to check today. Either way its going to pay Dr Nathan a visit on Monday. Fingers crossed it just the sender (which seems very common from what I have read).

I'm not stressed, just annoyed.  I've had about six hours use out of my car since getting it back -- that's after about 7 weeks off the road -- and now there is the possibility of another problem.  I'd kill for, oh, say a month of hassle free motoring.

Re:  cold start pressure, I didn't notice and I haven't had time to check today.  Either way its going to pay Dr Nathan a visit on Monday.  Fingers crossed it just the sender (which seems very common from what I have read).

RB26 oil pressure at idle 1.5 , @ 2000 rpm 3 and @ 6000 4.6 , at normal oil operating temperature , oil takes longer to get to normal temp than coolant .

Dont worry about cold temp pressure as it will vary depending on oil temp .

Pressure will vary depending on oil used and age of oil as well .

Edited by wrxhoon

Just to add another data point, I'm running 10w40,

I have:

4-5 @ cold idle and driving,

2 @ warm idle,

4 @ warm regular driving,

4-5 @ warm "vigorous" driving.

That all seems fine to me, and until a credable source convinces me otherwise, I'm happy with it. :D

Edit: Engine is a R32 RB20DET.

Edited by Oosh

i have a rebuilt RB25 less than 10,000km old and the oil pressure does a similar thing to what has been mentioned in this thread... in traffic or on reasonably warm days the idle oil pressure sometimes dips below the 2bar mark... it looks as if the guage is a bit sluggish and slow to react

not good for the heart after you have dropped 6k on an engine rebuild and the oil pressure looks sluggish... time for a new guage and sender methinks!

i have a rebuilt RB25 less than 10,000km old and the oil pressure does a similar thing to what has been mentioned in this thread... in traffic or on reasonably warm days the idle oil pressure sometimes dips below the 2bar mark... it looks as if the guage is a bit sluggish and slow to react

not good for the heart after you have dropped 6k on an engine rebuild and the oil pressure looks sluggish... time for a new guage and sender methinks!

Rb 25's have slightly different oil pressures .

Idle 1 , @ 2000 rpm 3.5 and @ 6000 rpm 5.6 , the reason its lower than rb26 at idle is the idle speed is lower on the rb 25 .

Thats how the oil gauges are slow to react , if you are worried get an aftermarket gauge .

A lot of rb 26's that have restrictors fitted will have higher oil pressure .

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • https://www.facebook.com/share/p/18rmVb1SKB/ 
    • The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...