Jump to content
SAU Community

Recommended Posts

I think my car is down on power compared to others I have heard about with simliar setups.

Current mods;

Nismo fuel pump

555cc Nismo Injectors

HKS GT2835 Pro S turbo (420ps)

Tomei 270 Degree cams

Full 3" exhaust.

Greddy Plenum

HKS front mount

HKS Fcon V pro ECU (Map sensor type)

So far the best power i have managed to produce is 320rwhp on 1.3 bar. To me it seems kind of average, cause i've heard of other people making 380-400 rwhp, on this turbo. The tune in my ecu was done in Japan and its fairly rich around low 11:1 afr but would this be making that much difference? How much HP should i be making? I'm changing over to a Power FC D-Jetro, just so i can get someone to tune it here in australia in hope to gain more, but what power levels should i expect, or am i expecting too much from this turbo?

Link to comment
https://www.sau.com.au/forums/topic/76857-how-much-power-should-i-be-making/
Share on other sites

I recently bought a GTR from Japan with an Impul tuned EPROM in it. The barstards glue the EPROM to the board so you cant read it - however this didn't stop me and I was able to pull the PROM and read the data. I really wasn't that impressed with there tune - very conservative all round, fuel was too rich in top end 11-10.5 and timing was very shy through power. Knock parameters where standard (not that it matters in the topend).

Could be a blocked cat as well or some kind of inlet restriciton. My advice would be to check the cat/restrictions and then either get the ECU re-tuned or PFC.

250rwkw sounds pretty good check the rb25det turbo upgrade dyno thread, i think theres at least one other 2535 turbo. your at about the max of the 2535 turbo as far as i can recall going from the ps rating. i dont see how the powerfc d-jetro will give you more power. it will be easier to tune with the normal powerfc and a z32

  • 1 month later...
Hey ookami, i also have the 2835 and managed 333rwhp on 15 pounds (tiny bit over 1 bar) without PowerFC. Something has to be holding you back...

you made 333hp with a stock ecu? you sure? My car is junk then!! I've got a greddy plenum and bigger cams and everything too!! Is yours the 2835 pro s with the weird Exhaust flange?

I recently bought a GTR from Japan with an Impul tuned EPROM in it.  The barstards glue the EPROM to the board so you cant read it - however this didn't stop me and I was able to pull the PROM and read the data.  I really wasn't that impressed with there tune - very conservative all round, fuel was too rich in top end 11-10.5 and timing was very shy through power.  Knock parameters where standard (not that it matters in the topend).  

Could be a blocked cat as well or some kind of inlet restriciton.  My advice would be to check the cat/restrictions and then either get the ECU re-tuned or PFC.

How did you manage to get the epoxy resin of the eprom? I also tried to pull one of a board, but my fingers aren't as strong as your.

some people must have weird dyno readings or something. I don't understand how they make more power on less boost. I know i would gain some power with a decent tune, but some people are claiming on stock injectors. how does that work?

I'd ditch the ecu and get yourself a powerfc, or if you really want something that has alot of features (and so you can toss the afm) get a link, haltec, or autronic.

****, you'll get alot more power with a good tune, judging by the mods you've already done.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeop... binned it   This will be a summary will not many pics atm and cbf  Fixed the samsonas - it was totally munched Put a new precision 7675 T4 on with proper split pulse mani Got to Sydney to get to car - drove to canberra to get racecar - drive back to sydney that night Next day all day at Plasmaman putting on new clamps cleaning some things up and adding another large engine oil cooler sitting at the rear above diffuser to keep things cooler Next day - Tuesday - on Dyno - killer wikid awesome pumped out really good numbers - more mid range and on lower boost levels Wednesday - first prac - all day again getting the suspension right - had to borrow front suspension again - out do a lap come in - out do a lap - in - what i had just couldnt handle the load at the more consistent higher speeds - got a lap in at the end of the day that was pretty reasonable  Put it this way that lap wouldve had me in 4th in Pro am for the whole event - with only 700 hp and used tyres Thurs first official prac day - lap out warm up - with above setting and 80% effort took corners 1,2,3 and into 4 car felt awesome -  rear came around out of nowhere bang into the wall near front on at whatever 140 kmph Done, over, gone Just one of those how did that happen apparently as all indications show nothing out of the ordinary Got to spend the rest of the time at the event like I hadnt done before - was actually Ok mainly as I had my family and my boy is 9 and got treated like a rockstar Long trip home, lost a trailer wheel in nowhere land, X5 airbag suspension gave up half way across nullabour and rode on bumps stops (its now completely fine) had to do a 19 hr drive day on day 3 as accommodation got screwed up so just had to keep driving till found a town with some Now to reassess - there is no easy fix there is no i'll just order that part and get it sent - we'll have a talk to people see what can happen and what the go is but at minimum its rebuild from scratch struts forward and alot of time effort and $ should and if I return and if but maybe/ when  I have the cage tied into the front strut towers - if I didnt have that things couldnt been worse you can say its just a front end but if you know what goes into these cars... you'll know what that actually means in reality   Car was very fast. Disappointing we just didnt get to show it     Apparently this is motorsport !  
    • Thanks, will do that.  Thankfully they still feel great.
    • Yeah man, absolutely. You can try pushing me all the way in swapping the R34 for an E9x M3 
    • It's almost certainly going to be some amount of pads compound transfer onto the rotors. It will probably go away after you've run them for a bit. If not, pull it all out, lightly sand the rotors, scuff the pads, and rebed.
    • no one recommending speedtek gearsets?   i'm in the same boat as Cosline but rwd, I am holding boost back in third to 600nm at the hubs to save the gear as i make nearly 750nm at the hubs on a mainline
×
×
  • Create New...