Jump to content
SAU Community

Recommended Posts

I'm after a set of 18x9.5 or 10 inch rims to suit a r32 gtr with good or new semi comp rubber for around $2500 landed. Waht types of packages are out there?

semi comp rubber (x4) alone in 18inch will be costing $2k+. new.

18inch rims in the widths that you are seeking can also cost around the $2k+ mark if you are looking for quality.

with the link provided, u can clearly see that one 18inch semi is $520 plus shipping.

http://page3.auctions.yahoo.co.jp/jp/auction/c46422791

admittedly, second hand tyres are cheaper.

for example,

new 18x9.5 or 18x10 Weds SA70 or Work CR Kai or similar wrapped in Semi comp rubber would land for $4370.

a set like this is very unlikely to pop up in the 2nd hand japanese market. the same goes for any 18inch wheel and semi comp tyre package.

another option would be to find a 2nd hand set of 18inch rims only..

perhaps a 2nd hand set of 18inch semis. the downside would be the shipping costs for 8 items.

still well exceeding the $2.5k budget.

  • Replies 345
  • Created
  • Last Reply

Top Posters In This Topic

gday rowdy,

its really hard to say at this stage seeing as they dont close for another few days.

sets like this we've been able to land for around the $2500 mark.

i dont want to say any more or less than this at this stage.

$2.5k ball park is good to work with.

Dammit, if these only were wider like in a 9.5 or 10 inch. 8.5 will be stretching 265 or 275 tyres.

TE37

19x8.5 +30 all round.

good for GTR also

114.3 5hole

bids close 25th/6

landed between $3100 and $3900

sogachin_c24-img600x450-1119191223te371.jpg

black LM GT4's?

114.3 5hole

18x9.5 +12 all round.

bids close 25/6

teppei20020516-img600x450-1119228809img_2006.jpg

These are respray's i guess? any other info about them? Wonder why the offset is +12 but +14 for the other LMGT4's (edit: nevermind , checked the Rays Japan website and they say +12 is the right BNR34 offset)

If you haven't guessed im after a set of 18 or 19 inch LMGT4's for my R34 GTR in gloss black - I guess any LMGT4 set would do as I could respray them...

Please send info :D

--------------------------------------------------------------------------------

Rays SE37 immaculate condition.

18x10 +-0 all round

perfect size and offset for the N1 GTR or widebody silvia.

how much??? would it be a alright fit on t r33 gtst??

thanks mate




  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...