Jump to content
SAU Community

Recommended Posts

  • Replies 345
  • Created
  • Last Reply

Top Posters In This Topic

Buddy Club P1 QF FORGED with comp rubber 7.4kg rim weight

18x10 +12 all round.

114.3 5 hole

Falken Azenis semi comp 245/40/18

GT-R suitable.

one slight scratch on one rim. No gutter damage whatsoever.

$3000 landed. ( coming soon )

kaireican-img600x450-1123988210dsc05354.jpg

sure thing Rick.

we so require a 50% securing deposit prior to bidding/purchasing.

Once we have secured the product, shipping takes approximately 6 weeks to reach your door. Once they have landed here in sydney, we request final payment prior to sending the product to you via local courier.

HOLY CRAP!

I was under the impression it was the whole asking price then we receive the goods?

HOLY CRAP!

I was under the impression it was the whole asking price then we receive the goods?

50% up front.

50% once goods land in Australia.

Goods not released until payment is made in full.

i think that makes it clear. :)

  • 2 weeks later...
NISMO LM GT3

18x10 +20 all round GT-R suitable.

two rims have very slight gutter mark.

Dunlop FM-901 rubber 275/35/18

Closing August 29th. This set will sell and won't be relisted.

$2700 landed

tera374638-img600x450-1122201523dscf0459.jpg

tera374638-img600x450-1122201562dscf0461.jpg

They relisted - 128,000 "buy it now" ! Tempting but does that rubber look fairly worn out to you? Can't tell, bad angles. What does the text say about it?

  • 2 weeks later...

TBee,

these are more suited to the R33 and R34.

however, being a 9.5" rim, the +12 offset will certainly bring the wheels out to the edge of the guards, perhaps lipping of the guards will be enough. will double check.

ok, just checked... these were originally on a R34.

i know 10" rims can fit under a R32 with a +22 to +25 offset.

given those specs, these rims are a 9.5" width, taking into consideration that the offsets are bringing the wheels out a further 10-12mm with only 6mm less rim on the outer, these wheels will be sitting approximately 6mm further out than a 10" with a +22ish offset.

slight rolling of the guards may be needed to get these babies to fit.

estimating between $2500 and $2800 landed at this stage.

How much do you think those GramLights 57C will go for ?

I'd be only really after something with almost brand new rubber?

Cheers

That set in particular closed nine days ago, as mentioned on the post.

( September 7th )

I can source out some other rims that may be of interest.

Do you have sizes in mind?

17 inch 9/9.5 wide? rubber included i pressume.

Cheers.

Volk Racing GT-C in BLACK

18x9 +18 all round.

GT-R suitable.

Bids close September 23rd.

moro3_2000-img600x450-1126833718img_1001.jpg

Work Meister S1

18x9.5 +20 all round. some minor gutter scuffs.

Yoko rubber. 265/35/18

6-7mm tread

Closing September 23rd

from $3600 landed

miyupapa11-img600x450-1126859273aomori_108.jpg




  • Similar Content

  • Latest Posts

    • Yeah I've had too many issues with knock off's on the BMW's. I don't want to do a job twice or more because the parts are shit.
    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
×
×
  • Create New...