Jump to content
SAU Community

Recommended Posts

It confirms that it is a 1 year warranty as we are dealing directly with an authorised Apex dealer and that was what was negotiated with no hassle.

Because that is what i have been assured by my Distributor.

It is part of the first post if you would care to read it:

1 year warranty, turn around time is less than 3 weeks. Just sent it me and I will take care of it.

Your question was answered before you asked it.

So no your post is not relavent to this group buy.

1 year warranty.

Dealing directly with an Authorised Apexi Dealer.

I quoted myself just incase you missed it in the first post that i responded to you.

  • Replies 87
  • Created
  • Last Reply

Top Posters In This Topic

No Prabs mate

We are dealing with Apexi Japan not Apexi USA

For warranty the Power Fc is to be sent back to our distributor in Japan and will be subject to the warranty guidelines set by APEXI int. but includes 1 year warranty which is subject to those same guidelines.

put me down for a R33 Gts25t

what will be the turn around time once we get 30???

do we need all 30 to have paid before we can get ours?

just dont want to be held up by some 17yo punk without money... :)

Nte

Turn around time will be about 2 weeks once all buyers have paid.

3 days standard for clearance for bank transfer + delivery from Japan.

All Power Fc's will be delivered seperately and all will include a tracking number so everyone can monitor the delivery process.

I have been advised by Slide that a 12 month warranty HAS been confirmed for this product. gR33ddy - please refrain from posting in here again (seeing as you are advertising a similar group buy).

Christian

is someone able to tell me why its only the R32 power Fc's that r more expensive? i mean RB20DET would have to be one of the most common nissan engines around so y so much more expensive?

AP Engineering Power FC without Comander for R32GTST (RB20DET) will be inclusive in this group buy at a cost of $1115

$1420 with hand controller

Thanks Guys

AP Engineering Power FC without Comander for R32GTST (RB20DET) will be inclusive in this group buy at a cost of $1115

$1420 with hand controller

Thanks

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
×
×
  • Create New...