Jump to content
SAU Community

Recommended Posts

Hi, All

I 'm looking for next family ride, now it's only a matter of toss between inport myself or buy local.

However I need your advice in term of " how to identify crash repaired " and the "Odometer (spell) reading".

I have been to a few yard in Sydney and check up different imports, some of them have lower kilometers, which is like a 98 model with 35000km on it, or a 97 model with 52000km on it. does this sounds right to you? Most auction sheet I have saw so far all like 60K +, yes, I do see some lower one in auction with grade 4.5 /4 and sold for outside our budget, but what happen to those already here, i.e. a 98' with 35000km chamonix ask for 26000 on a QLD dealer's website? Could it be possible? how do you know the odometer is original reading? can ppl trick it?

and how / where to check if this delica has been crash repaired?

Link to comment
https://www.sau.com.au/forums/topic/77312-how-to-check-if-car-crash-repaired/
Share on other sites

The way i usually tell if a vehicle has been crash repaired is pretty much go over the whole car with a fine tooth comb (thoroughly). Check all seam seals (cracks, inconsistancy, different on one side to the other), check all edges for fuzzy paint edges, check all window seals for oversparay (especially on 1/4 panel - roof area, check this area for paint fade-outs too), check panels for inconsistant peel, dullness, defects, shrinkback ect. check for colour differences from panel to panel. make sure the car is in a well lit area and look on an angle down the sides, check for rippley/wavey panels. make sure all gaps are consistant. make sure doors, bonnet, boot all open/close without problems. Always good if you can check underneath the car too, chassis rails, under guards ect. It takes awhile to check all these things, but well worth it in the end, hope that helps.

sam

Whites can have a few variations, darker-lighter, dirty-clean, red-green and yellow-blue

Silvers most obvious are light-dark, fine-coarse, there are also varied colour undertones to look for, most comon is a silver is yellow-blue.

The best way to pick a colour variation is to check the flip, to do this, make sure the car is in the sunlight (also helps if the car is clean) and look on an angle towards the two panels.

im a spray painter btw, so i gotta do this stuff everyday :D

Dont bother looking at the odo to tell the k's, they can be wound back easily, and just as easily swapped for another one. Look at the steering wheel and pedals for wear, aswell as the drivers seat condition etc. A car with 50k's on it and a worn out steering wheel has something that doesn't add up.

At the end of the day the k's dont matter, its the condition thats important.

The way i usually tell if a vehicle has been crash repaired is pretty much go over the whole car with a fine tooth comb (thoroughly). Check all seam seals (cracks, inconsistancy, different on one side to the other), check all edges for fuzzy paint edges, check all window seals for oversparay (especially on 1/4 panel - roof area, check this area for paint fade-outs too), check panels for inconsistant peel, dullness, defects, shrinkback ect. check for colour differences from panel to panel. make sure the car is in a well lit area and look on an angle down the sides, check for rippley/wavey panels. make sure all gaps are consistant. make sure doors, bonnet, boot all open/close without problems. Always good if you can check underneath the car too, chassis rails, under guards ect. It takes awhile to check all these things, but well worth it in the end, hope that helps.

sam

thats a good explanation of what to do, its what i was going to say!

look for plastic welding around the front of the car as sign of minor front end accidents..

most imports have been resprayed, or at least a large part of the car has been painted.. probably more important than minor accident damage is rust, check for sgins of corrosion around the engine bay on the alloy parts, there is a lot of rusty imports around, they usually paint the whole car so its not obvious but u can tell especially by looking in the engine bay, boot and under the car (either rusty or covered in fresh tar)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah pretty impressive hey, good to see quality products not over-shooting their prices. That's what drew me to buy the hypergear turbo, just a shame I've never got the chance to see it in action
    • Thank you GTSBoy and MBS206 I have done the compression test with the motor out of the vehicle, reason for the test was to see if I needed to remove the head and do rings etc while its out. I'm in the process of respraying the vehicle and tidying up a few things. Story behind it all is I've just purchased the skyline and it was running when I got it, never drove it on the street though as I wanted to pull it down and do it all up again before registering it. the gentleman I purchased it from told me the motor has a forged bottom end and has a decent tune through it but I was going to pull the sump off anyway to see if it is a forged bottom end. that's why I thought id do a compression test beforehand. 
    • Man, I'm kind of amazed that the price of the turbo has not changed in 7 years. Everything else is inflating beyond reason, but not this? Good on Tao / hypergear I guess? Anyways, good luck with the sale!
    • I'm selling my brand new, in the box, never used Hypergear ATR45 - and I had some additions I paid for a few yrs back when I purchased it. Never ended up having the rest of the money to add all the mods at once, so I just ended up slowly selling each part. I originally had it internally gated, with the dump pipe, however I found it was incompatible with what I was going to use it for, so I contacted (I think Ken) from Hypergear, and he and I messaged back and forth & he got me to ship the turbo back, where they modified it & made it externally gated, and gave me the 5 bolt dump pipe attachment for custom welding. (Photos below) This turbo like I said has never touched the inside of an engine bay, it's completely brand new, never used, been sitting in the same box it arrived in, covered in plastic & all. Below are the photos of it: And while the guys at Hypergear were making it in-shop, they sent me some photos of the process: I'm looking at selling this just because I'm in need of the money right now, and don't have plans on modifying the 34 anytime soon - and from reviews & peformance sheets, this turbo had amazing results back when I was researching. The turbo was purchased in 2018 for $1.9k, with the mods I got added on. Looking at the website now, for the same turbo they sell (ATR45SAT), with the current addons it adds up to $1830 for the turbo Current addons included: - Bolted dump adaptor - Ball bearing CHRA - Braided oil feeding line So I'm looking to possibly sell it for around $1800, with shipping included in that 1.8k, It cost me around $120 to ship - so yeah thought I'd throw it out there and see if anyone was interested in purchasing. Cheers!
×
×
  • Create New...