Jump to content
SAU Community

Friday Night Cruise Sessions - Palm Beach & Pizza Cruise - 24/6/05


Recommended Posts

Its time for another Friday nighter people.

Due to the growing popularity of the usual meeting spot we will not be meeting at the Chatswood Archer St Carpark, instead the new and improved meeting point is as follows:

Time: 9pm for an 9:30pm departure

Location: Chatswood Chase Carpark - Lower level (Entrance off Victoria Ave)

Destination: Palm Beach via the Northern Beaches with a stop off for Pizza at Newport on the way.

Some things to note:

* We will meet just inside the entrance of the carpark at Chatswood Chase. Not onlly is there more than ample parking in here, but it is under cover and out of sight.

* If you have a 2 way radio, bring it.

* Heroes and drag racers need not apply, anyone who attends and decides to do burnouts, drive like and idiot, or do anything that attracts attention to the group will have their plates reported to the police. We have never had a problem with the Northern Beaches police and we have been doing this particular cruise for over 3 years, anyone that puts our reputation at risk will be told to leave.

Register your interest here :(

Cheers,

Nick

  • Replies 184
  • Created
  • Last Reply

Top Posters In This Topic

Nick,

Can't make it thought it was departure 9.30 like previous ones, have an exam on which doesn't finish till 8.40..............sorry mate

Aye~~my exam finish on Thurs~~hee hee

Yeah~~

make it 9:30pm or 9:00pm~~i finish work at 7:30~~~and i really wanna come~~

oh i m not quiet sure about the meeting place~~

it s that the 5 level carpark next to mandarine center??

if so , what coloar is the level??~~~




  • Similar Content

  • Latest Posts

    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • It's been quite the ordeal but hey, at least you figured it out.
    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
×
×
  • Create New...