Jump to content
SAU Community

Recommended Posts

Hi Guys,

Does anyone have a list / map of the fuses for an R34 GTT (internal)?

I’m having trouble with my Front Wipers. I can’t see any fuses that are blown, but there are a number of slots that have no fuses at all.

I assume there’s plastic cover that goes over the fuse panel. My cover is missing

Maybe my wiper fuse is missing???

If someone can snap a photo or has a document with them listed, that would be great!!

Thanks for your help

PEAR

Hi Guys,

This is the kind of thing I'm looking for but for an R34 GTT

Thanks

PEAR

-------------------------------------------------

SKYLINE R33 Fusebox

In Cabin Fuse box:

Left column, top to bottom

10A REAR WIPER

10A ANTI-STOP (ABS PERHAPS???????)

10A STARTER INDICATOR

10A ROOM LAMP

10A STOP LAMP

10A ELECTRICS

10A ENGINE CONTROL

10A HAZARD LAMP

15A FOG LAMP

10A TURN SIGNAL

10A METERS

10A ELECTRICS

Right column, top to bottom

10A SHIFT LOCK

10A A/T CONTROL

10A AIR CONDITIONER

10A ENGINE CONTROL

10A AIR BAG

20A BLOWER MOTOR

20A BLOWER MOTOR

10A AUDIO

15A CIGARETTE LIGHTER

20A FRONT WIPER

10A MIRROR CONTROL

20A REAR DEFOGGER

Boot Fusebox

Reading from top to bottom

65A - Main

45A - Blower

30A - 4WD/LSD

30A - IGN SW

15A - FUEL PUMP

20A - HEAD L RH

20A - HEAD L LH

10A - ALT S (Alternator perhaps???????)

10A - TAIL L

20A - HICAS

15A - AUDIO

I don't think this is what you want but this is the one under the bonnet.

Thanks mate, I have this one ok (under my bonnet).

I'm looking for inside fuse panel - Drivers side, under dask, near Accelerator Pedal...

but thanks for trying!!

PEAR

Thanks mate, I have this one ok (under my bonnet).

I'm looking for inside fuse panel - Drivers side, under dask, near Accelerator Pedal...

but thanks for trying!!  

PEAR

Hi Guys,

Rezz from the Japan forum did some translating for me!!

Front Wipers are position #6.

This thread can now be closed (if you like)

Thanks!

PEAR

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...