Jump to content
SAU Community

Recommended Posts

Hey all,

Came down for the dyno day, which was a rather good day if I say so myself and also put my car in on the dyno. This is the result I got on the dyno.

IMG_0034.JPG

Now even though that was the lowest power figure out of the all the turbo cars :( , it seems too high for a stock RB20DET with catback exhaust and pod filter. Converted to kw it is 144rwkw which is about 5-10kw higher than what it should be. Now I don't know much about dyno results and after checking out the latest version of HPI, there RB20DET with the same mods as me plus a FMIC made only 145rwkw which is 1kw more than mine. How can that be?

One thing I noticed in difference between my dyno result and the HPI car is that there intake temperature was 19 degrees while mine was 45 degrees? Not sure how such a high difference in temperature could occur but could it have inflated my result to give an incorrect reading?

Can anyone clear this up for me and any comments from the hyperdrive guys would be appreciated.

Cheers,

Scott

Link to comment
https://www.sau.com.au/forums/topic/77714-uncanny-dyno-results/
Share on other sites

Dynos differ depending on how they are set up.

The HPI one may not have been in shootout mode so I'd say those figures are close enough not to worry about.

Your 32 seems pretty healthy anyway which is always good to know.

The intake temps are interesting though. Was that taken at the inlet manifold or air inlet?

If you have a pod without a partition, the ambient temperature would increase the reading from the temp probe, and therefore change the reading. A higher intake temp gives a higher corrected figure.

If the temp probe is sitting against anything in the engine bay, you may get an over inflated intake temp - as the air coming into the pod is coming straight through the open bonnet.

By comparison, my intake temps were 26 degrees, but I am using a partition. The run was done within a couple of minutes of my car arriving from a long drive. Still somewhat interesting as the ambient air temp would have probably been closer to 12-14deg at the time.

This is a good example of the fact it is almost impossible to compare dyno figures 100% accurately. I am quite sure the air going into your car was not 20 degrees warmer than the air going into mine.

Dyno is for tuning - they give you a good idea of where AF ratios are at, how and where power is delivered and where there may be problems with the current setup. Peak power should be a guide only.

']dude mine made completely stock , bar an intercooler, 184.5 rwhp, so your power isnt bad at all

Not bad but how much of a gain would a catback and pod filter give? On top of that result? Because if it's a +15rwhp gain, we would still be be in the same problem again.

No not really, because then it would seem LOW not high for the mods you have.

End of they day a dyno is a tuning tool, next time you do a mod, re run it, and see what improvements you have made. Ken and Lumpy run a very professional show down there, so I doubt anything was done to make your numbers wrong

Im documenting every mod i do on antilag, so check the main site every once in a while to see what comes of it. Might give you some insight to what mods you could do yourself

Cheers

TJ

my car only got 226rwhp with similar mods :)

Only difference is mines S1 and ive heard its alot more spikey when more boost is added, it dropped 40rwhp towards the top end in one spike. Im going for a apexi power fc when i can get the $$ together to fix

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...