Jump to content
SAU Community

Recommended Posts

For those who couldn't stay overnight for DECA, we can cruise together on the SAT Morning!

Timing is base on your input then i'll edit my post. Meeting would be best at the Shell servo under the westgate brigde.

SthEast ppl can meet up with me at Mega Mart Chaddy. Time? Again, waiting for your input otherwise i assume it'll be really early in the morning.

Cheers

Link to comment
https://www.sau.com.au/forums/topic/77900-deca-cruise-sat-morning/
Share on other sites

Westgate Shell is not a great spot - kinda heading the wrong way :rofl:

Most direct route is Hume to Seymour then Goulburn Valley HWY to Shepparton.

Usual northern point of McMobil on the Hume, just North of the WRR exit might be better?

Say @ 6.00am

Is an easy meet point for North, West and East (WRR from Greensborough).

Central and South East - go Monash, through tunnel, over Bolte, onto Tulla, onto WRR to Hume. Needs eTag, but by golly you should all have one by now - or get a daypass.

Megamart is a good meet point - @ 5.30am

West: I'll meet you (and convoy) at McMobil at 6.00am

Greg: SMS me your address (0417 037 520) and I'll pick you up at 5.30am.

You can sleep in the car :(

Westgate Shell is not a great spot - kinda heading the wrong way ;)

Most direct route is Hume to Seymour then Goulburn Valley HWY to Shepparton.

Usual northern point of McMobil on the Hume, just North of the WRR exit might be better?

McMobil?

I should be there, 6am.. ugh. What's our estimated travel time to get there?

-Patrick

Megamart is a good meet point - @ 5.30am

West: I'll meet you (and convoy) at McMobil at 6.00am

Greg: SMS me your address (0417 037 520) and I'll pick you up at 5.30am.  

You can sleep in the car :D

Where is Mcmobil guys? :uh-huh: So we meet at mea mart or Mcmobil?

Just to confirm I'll be at McMobil - ideally leaving no later than 6.15am

Bring CBs if you have them - we'll be on CH 15 if you are running late.

My mob: 0417 037 520

Will update what sort of car I'll be in a bit later on (unknown at this stage - but not Golgo or Lada 1 or 2). I can guarantee it wont be exciting :rofl:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
    • I saw your intro update, are you sure you've actually had a starter motor failure? You mention it could be the alarm causing it. I'm assuming you've got a no start issue, but what are the exact symptoms, as there could be a few reasons it has stopped wanting to start.
×
×
  • Create New...