Jump to content
SAU Community

Recommended Posts

I went out for a spin last night, everything was running sweet for half an hour or so untill all of a sudden the car started missing under load, basically as soon as it makes more than 4psi. It was like someone flicked a switch!

I have read thousands of posts about plugs and coils but i'm not sure this is the same thing.

The car is a R33 Series 1. Stock except for:-

3 inch turbo back exhaust

K&N filter eliment

Boost solinoid set to permanent high boost

All mods have done over 20000KM

The problem

missing when under load/boosting more than 4psi(approx),

runs smooth off boost, even at higher revs as long as it's not boosting

Does a coil pack or plugs go off this quickly or should i be looking for something else. It was running fine, then three seconds later it was running like shit!

Any help very much appreciated

Link to comment
https://www.sau.com.au/forums/topic/78337-mis-under-load/
Share on other sites

will be pulling the plugs later today. i have platnums in there , if i think one could possibly be a little fowled i'll put a brand new set of coppers in.

the boost is standard, i have just hardwired the standard high/low solenoid.

as for the revs, it has an occasional mis around 3000 and it's really bad around 4000.

i tried driving through the miss but it is the same up higher

Link to comment
https://www.sau.com.au/forums/topic/78337-mis-under-load/#findComment-1430515
Share on other sites

ok, put new plugs in tonight, the missing isn't as bad now.

i think this could be due to me regapping the new plugs down to .8, the old ones were 1.1. So it looks like it was the coils after all.

I managed to pick up a bit more boost too, i must have sealed a leak when i was re-attaching everything.

Does anyone know where to get some spitfire coils in Australia at a reasonable price? I know there is a group buy but my car is a daily driver and i don't want to have to wait that long.

Link to comment
https://www.sau.com.au/forums/topic/78337-mis-under-load/#findComment-1433515
Share on other sites

A friend of my had problems with the colis in his getz (not a skyline but still has spark plugs). They were leaking bad (big sparks from the coils at night). He took it to the dealer and they were able to read the voltage off each coil.

But if you want to replace one coil pack you might aswell do all of them otherwise the problem will repeat itself down the track.

So as sumo said check out that other thread

Link to comment
https://www.sau.com.au/forums/topic/78337-mis-under-load/#findComment-1436230
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You don’t need to use full throttle all the time to break these blocks, 500kw at the wheels in more then enough to break them even with an occasional squirt. Hell I’ve seen them break under 400kw
    • A work around is to install the R35 card style AFM/MAF on the cold side of the intercooler piping and the BOV on the hot side piping. Works well, also you can combat the revs dropping by adding a bit more ignition timing on the idle ignition timing table to slow the rate of RPM drop.
    • Understood. If you dont have a ridiculous limit,  Tune, T's and P's are in check, and arent bashing it all the time and doing the due deligence for maintenance(inc oil analysis) then its pretty safe. 100% agree, let your right food control it to some extent.
    • So these external kits with the machined block for remote solenoid mount will only work on a NEO head and RB30 or RB26 bottom end   For an R33 head on a 26 bottom end the remote vct kit is to resolve RB26 manifold adaptor plates etc  IF you try to use the remote VCT on an RB30 or RB26 bottom end with an R33 head then  you can starve the cam journal??? I have one of these kits from bits I had years ago before plans changed  I don't understand how that tracks with this video   https://youtu.be/RuPiI22Mplk?feature=shared   This looks like I can run the v termite vct kit to feed the VCT on an R33 head on an RB26 bottom end?!?!?   Lol.... don't v have these problems on RB20s
    • Yeah i know that MAF is no no for this type of BoV. The engine has no BoV and "hose/pipes" ..it was all deleted (or probably it was not even on the engine when it was bought  ) It does that "sutututu" noise which i kinda do not want(atmospheric is better IMO...but standalone ECU)  What are the cons of running without blow off on stock RB25DET NEO. It running 5-7 PSI max (it has boost controller)   EDIT: and can Nistune be "tuned" to know there is no BoV to i dont know "know" and be better for a car? I read so many info about no BoV. One guy saying it is bad and hurting the turbo/engine/car and other that it does not...  
×
×
  • Create New...