Jump to content
SAU Community

Recommended Posts

just bought and fitted a set of split fire coils and planning to regap spark plugs. im want to gap them at 1.1 but am thinking why stop there? why not 1.5 or more?

I doubt they could run a spark that hectic ,I just recieved mine yesterday yet to install let us now what gap you can run b4 it breaks up (can't be bothered gapping the plugs so just gonna buy 1.1mm )

although the splitfire coils may be an improvement over standard coils it will never have the power of a CDI system that can run big gaps under high cylinder pressures.

let us know how you go though, doubt it will do 1.5mm gap myself.

That sounds like an interesting idea. I'm running a set of stock coils in my car atm, and they are in very good condition. I run a 1.1mm gap no problems at 10psi.

Perhaps if the splitfires are better, you might be able to run a bigger gap. Only one way to find out. Try it.

And the point of this being what?

:confused: :confused: :confused: :chairshot :chairshot

More efficient combustion ,more fuel burnt equals more power

I found this article on a site ....We haven't seen any benefits of gaps beyond 0.045-inch, so that should be the outer limit of sparkplug gap. Don't re-gap sparkplugs too many times because the ground strap metal will fatigue and may break. If your engine makes more than 75 horsepower per cylinder, gap the plugs only once. If your engine makes more than 100 horsepower per cylinder and/or sees extended periods of high RPM and/or high boost, we'd have to say don't gap the sparkplugs at all! (Here, it pays to use high-quality plugs that have a consistent gap as-manufactured.)

I done this little exercise as i have splitfire coils. Gapped at 1.1mm and running 20psi, it missed. Gapped them down to .95 and it still missed. Just above .8 i gapped them at and now i have no miss. Remember im running alot more boost though.

There might be something about this on the NGK website. And I recall someone (Zoom! or Autospeed) did this comparison a while ago.

You need to have a coil that can generate enough energy to jump the plug gap. Even if if can, it may be so borderline in strength that it actually causes a worse burn than the narrower gap could produce. This is often why you need to gap down at higher boost levels - the poor spark is more susceptible to the higher cylinder pressures that come with increased boost.

There's a lot of physics and chemistry involved - it's not just a simple matter of saying that a bigger gap will produce a better burn.

:confused:  :confused:  :confused:  :chairshot  :chairshot  

More efficient combustion ,more fuel burnt equals more power

I found this article on a site ....We haven't seen any benefits of gaps beyond 0.045-inch, so that should be the outer limit of sparkplug gap. Don't re-gap sparkplugs too many times because the ground strap metal will fatigue and may break. If your engine makes more than 75 horsepower per cylinder, gap the plugs only once. If your engine makes more than 100 horsepower per cylinder and/or sees extended periods of high RPM and/or high boost, we'd have to say don't gap the sparkplugs at all! (Here, it pays to use high-quality plugs that have a consistent gap as-manufactured.)

sorry to say this: but dave got :Owned:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nope.    Grab a varex and turn it down as you get close to home, win win? 
    • So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
×
×
  • Create New...