Jump to content
SAU Community

PFC n Injectors with rebuild or after?

Suspense

By Suspense,
in Engines & Forced Induction

 Share

Recommended Posts

Suspense Proficient

Suspense

Posted
Posted

ATM my engine is out gettin rebuilt. it will be tuned to push out 240rwkw with a gcg hiflow.

Currently i have stock ECU and stock injectors.

I want to know would you recommend that i get the injectors and PFC in during the rebuild process, or after the moter has been run in? The later enabling the car to be revved up in the tuning process without damaging my new engine.

Thanx in Advance

StockyMcStock Proficient

StockyMcStock

Posted
Posted

run it in with standard management on the smallest possible boost level you can (try disconnecting the wastegate so the flap is open all the time for example) for the first 500kms then fit the injectors and PFC, trim the fuel map by the relevant factor so you can drive it to the dyno. make sure you change the oil at 50km, then at 250 and maybe again at 500 just to be safe. castrol GTX (cheapest oil you can get) is pretty good for the first 5000km.

4door_Sleeper Veteran

4door_Sleeper

Posted
Posted
run it in with standard management on the smallest possible boost level you can (try disconnecting the wastegate so the flap is open all the time for example) for the first 500kms then fit the injectors and PFC, trim the fuel map by the relevant factor so you can drive it to the dyno. make sure you change the oil at 50km, then at 250 and maybe again at 500 just to be safe. castrol GTX (cheapest oil you can get) is pretty good for the first 5000km.

If a motor is built correctly there is no need to baby it like this. You do need to bed in the rings etc but the engine shop should do this before you are given the car back.

I agree with the frequent oil changes, but I dont recall seeing Schumaker touring around the F1 track with a "please overtake - running in" sighn on the back of the car. (and those motors are tuned to the limit) Likewise Nissan dont insist on GTR's beeing run in on low boost, the car is ready to go from the moment you pick it up.

I am not advocating you thrash the engine, but babying it can also be bad in the long run.

Suspense Proficient

Suspense

Posted
  • Author
Posted

first 50km my car will be on dyno, then i gonan drop the oil, drive for 500km drop the oil.

but boost level will be 10psi is, just keep it under 3000rpm... should be right.

just wanted to know about installing the pfc n injectors... looks like i will do it after the engine is run in....

StockyMcStock Proficient

StockyMcStock

Posted
Posted

lol @ comparison with the cosworth formula 1 engines, not really relevant at all ;)

Suspense: latest ideas on running in road engines is to use bodgy low-grade non synthetic oil. to bed the rings in load it up in tall gears but don't rev the crap out of it. large run-in times are not required, maybe 50km and it should be ready to go. personally i would change the oil at 50, 250, 500, 1000 then every 5000 with synthetic of your choice. everyone has different ideas on oil change frequency during run-in but after seeing what came out in the first 2 oil changes on the last engine i saw run-in, i would be doing it as described above.

4door_Sleeper Veteran

4door_Sleeper

Posted
Posted
lol @ comparison with the cosworth formula 1 engines, not really relevant at all ;)

Lets see, Pistons (check), Rings (check), Valves (check), internal combustion engine (check) - I'd say they are both the same. Admittedly the F1 engine is built to tighter tolerances but they are almost identical.

PS dont use ANY DODGY oil, use the good stuff. (non-synthetic of course). Pennzoil and others manufacture special oils for running in engines if you ask a good retailer they should be able to get it for you.

Cubes Grand Master

Cubes

Posted
Posted

I've been told by quite a few people not to run it in with boost.

Chris Milton Engineering (Well known for their involvement in GroupA) and also my engine Builder Andrew.

I wired open my wastegate and drove everywhere with a flat foot changing up around 3000-3500rpm with the occasional 4000rpm.

Gear Deceleration is very bad for a motor that is being run in, simply drop it in neutral.

I used Penrite Running-In oil, I changed the oil multiple times within the first 1500km's then I went to a Motul Mineral 10w30 oil. I used that until the motor had done 10,000km's then went synthetic.

My reason for using mineral for 10,000km's is the motor wasn't ran in on a dyno.

I made sure the rings had bed in properly. :P

They have appeared to, even with the largest recommended bore to piston clearance Wiseco recommend, it uses ZERO oil over a 5000km' oil change, its now done 16,000km's.

There is zero blow by in to the intake piping. Everything is as clean as a whistle.

NZM.031 Grand Master

NZM.031

Posted
Posted

i say do it all at once. its easier. a proper build will not need much engine run in time, 1000kms will be well and trully run in.

a proper tuner will be able to set the pfc up to a safe tune without even checking it. slight road tune or dyno tune will be able to get it to a safe level while running in.

then at 1000kms you can get it properly dyno tuned for the boost of your choice.

cheers

Linton.

Cubes Grand Master

Cubes

Posted
Posted

Mine wasn't run in on the dyno, it also still had a little blow by at 1500km's. Having still a little blow by at 1500km's meant that it wasn't completely run in.

I extended my run-in to 10,000km's before synthetic oil as many manufactures recommend (Mainly in the US).

Now I have zero blow by. :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...