Jump to content
SAU Community

GTR injectors AGAIN!

Waldo

By Waldo,
in Engines & Forced Induction

 Share

Recommended Posts

Waldo Proficient

Waldo

Posted
Posted

hey guys i really need to know how to wire inline resitors in my rb20 for gtr injectors to work with my power fc, i need to know exactly what resistors i need to put in and also what resistance the circuit has to be to make them run, i dont want to blow up my precious power fc,

thanx for al you help

regards luke

Link to comment
https://www.sau.com.au/forums/topic/79958-gtr-injectors-again/
Share on other sites
predator Grand Master

predator

Posted
Posted

There was a guide on how to make them.. was very easy and would cost you about $5 in parts.. I believe it had to do with wiring a resistor on the "active" line of each injector. It was in a stupid place on here (wanted section??) and can't find it for the life of me anymore.

Roy Grand Master

Roy

Posted
Posted
so if i just get a gtr ballast resistor i just plug that into the loom do i and it will work perfect?

Its not plug in, it requires soldering whether you use the Nissan ballast resistor or make your own usign resistors from Jaycar.

If you look in the tutorial section i did a thread to help ppl get started. Outside of that it is easy to cut into theloom and solder it all up, just take it slow and triple check everything. If you were in Melb id be happy to do it, including installing injetors its about a 6hr job from start to finish, including removing coil pack covers, inlet piping, taping up the loom etc etc

Ed G Grand Master

Ed G

Posted
Posted
Mine was 13 ohms with the GTR resistor pack in and 3.5 ohns with resistor pack out.;)

Thanks SK, In the workshop manual it states 5k for the resistor pack :confused:

even so 13k seems a little high if the ecu has the same mosfet transistors as the rb20 ecu

Ed G Grand Master

Ed G

Posted
Posted
Cant remember, i did measure it to check that i had it all wired up correctly. Easisest thing to do is when you are removing the injectors just check the resistance of the GTR injector with the RB20 injector.  

I seem to remember the ballast resistor was about 5-6ohms

well that confirms what the workshop manual states...

Waldo Proficient

Waldo

Posted
  • Author
Posted

so if i simply get a gtr ballast box, i just have to cut and solder each injector positive feed into each of the wires coming out of the ballast box?, if i do it the other way as in wireing resitors inline, do i just cut the main feed to the injector and wire an inline resitor into it, if so what size resitor is needed to do this.

  • 2 weeks later...
predator Grand Master

predator

Posted
Posted

you are best off getting the heavy duty ceramic ones - I think they are the 1watt.. they are big and square. I'd say if you wrapped that in plenty of electrical tape, and soldered properly you shouldn't have a problem I wouldn't think.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • V35Newbie
      After market rear camber arm adjustment

      By V35Newbie · Posted

      I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • V35Newbie
      After market rear camber arm adjustment

      By V35Newbie · Posted

      I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
    • GTSBoy
      Unpeeling the Orange

      By GTSBoy · Posted

      Heh. I copied the link to the video direct, instead of the thread I mentioned. But the video is the main value content anyway. Otherwise, yes, in Europe, surely you'd be expected to buy local. Being whichever flavour of Michelin, Continental or Pirelli suits your usage model.
×
×
  • Create New...