Jump to content
SAU Community

GTR injectors AGAIN!

Waldo

By Waldo,
in Engines & Forced Induction

 Share

Recommended Posts

Waldo Proficient

Waldo

Posted
Posted

hey guys i really need to know how to wire inline resitors in my rb20 for gtr injectors to work with my power fc, i need to know exactly what resistors i need to put in and also what resistance the circuit has to be to make them run, i dont want to blow up my precious power fc,

thanx for al you help

regards luke

Link to comment
https://www.sau.com.au/forums/topic/79958-gtr-injectors-again/
Share on other sites
predator Grand Master

predator

Posted
Posted

There was a guide on how to make them.. was very easy and would cost you about $5 in parts.. I believe it had to do with wiring a resistor on the "active" line of each injector. It was in a stupid place on here (wanted section??) and can't find it for the life of me anymore.

Roy Grand Master

Roy

Posted
Posted
so if i just get a gtr ballast resistor i just plug that into the loom do i and it will work perfect?

Its not plug in, it requires soldering whether you use the Nissan ballast resistor or make your own usign resistors from Jaycar.

If you look in the tutorial section i did a thread to help ppl get started. Outside of that it is easy to cut into theloom and solder it all up, just take it slow and triple check everything. If you were in Melb id be happy to do it, including installing injetors its about a 6hr job from start to finish, including removing coil pack covers, inlet piping, taping up the loom etc etc

Ed G Grand Master

Ed G

Posted
Posted
Mine was 13 ohms with the GTR resistor pack in and 3.5 ohns with resistor pack out.;)

Thanks SK, In the workshop manual it states 5k for the resistor pack :confused:

even so 13k seems a little high if the ecu has the same mosfet transistors as the rb20 ecu

Ed G Grand Master

Ed G

Posted
Posted
Cant remember, i did measure it to check that i had it all wired up correctly. Easisest thing to do is when you are removing the injectors just check the resistance of the GTR injector with the RB20 injector.  

I seem to remember the ballast resistor was about 5-6ohms

well that confirms what the workshop manual states...

Waldo Proficient

Waldo

Posted
  • Author
Posted

so if i simply get a gtr ballast box, i just have to cut and solder each injector positive feed into each of the wires coming out of the ballast box?, if i do it the other way as in wireing resitors inline, do i just cut the main feed to the injector and wire an inline resitor into it, if so what size resitor is needed to do this.

  • 2 weeks later...
predator Grand Master

predator

Posted
Posted

you are best off getting the heavy duty ceramic ones - I think they are the 1watt.. they are big and square. I'd say if you wrapped that in plenty of electrical tape, and soldered properly you shouldn't have a problem I wouldn't think.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      KW only offers a set for the R32 GTR. Popular options are D2 racing, Ksport or Öhlins. I have a D2 Racing coilover set, though I don't know for sure which one.
    • GTSBoy
      Unpeeling the Orange

      By GTSBoy · Posted

      Well, the good news is you have more than one very good option for new coilovers in and around your country. Worth the drive over to KW to talk about GTR stuff.
    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      Fair enough, I am in no way a tire expert so I'm not familiar with all the terms and conditions. I'll definitely note down the AD09 to potentially try in the future. Rain is not too big of a concern for now as I will probably only drive in the rain when I have to. And considering I still lack experience driving the GTR I'd more than likely take it easy too. I have coilovers in the car but as I barely got to drive so far I never bothered to even check if they are adjustable haha. The suspension is almost entirely old and worn as well so I suppose when I eventually fix that in the future that would make a huge difference.
    • PranK
      My BMW 335i

      By PranK · Posted

      There's not a great deal to report here .... except ...... FOR .... LSD!!!  I bought a Quaife LSD from the UK and shipped it here .... Wish I'd just bought locally cause the shipping and duty was $700! But there were so many diffs used in the E90s I just wanted to be absolutely certain I was getting the right one so I spoke with a supplier in the UK who builds race cars and they have heaps of experience with the E90s.  I pulled the diff out which was seriously awesome - I've never done anything like that before, I must have watched 1000 videos on YT about it as well as consulting the Bentley manual. It was super easy in the end. The diff was delivered to the awesome folks at Hornsby Diffs and will be back in a few weeks. I also replaced the diff bushings with some Nolathane ones.  Really looking forward to getting it back and getting back to the track or even the skidpan.
    • Dose Pipe Sutututu
      Unpeeling the Orange

      By Dose Pipe Sutututu · Posted

      yeah... the 13kg/mm springs weren't always in there, I had 10kg/mm but doing a few SMSP commanded heavier front springs. It's so good now going into T1 and T2, just need more seat time and real tyres.
×
×
  • Create New...