Jump to content
SAU Community

Recommended Posts

so the GTR owners have a thread like this, so i thought i'd make up one for us ones that drive gts-t's n gt-t's ( older skyline owners R31 n such can post to ).

k so i've spent roughly.... close to 30 thousand on my car, thats a fair bit of money lol, how much have the rest of you spent to date, or plan on spending in the future???

car: '94 R33 Gts-t..

where the money went.....

$14,500 purchase price,

$7,000 smash repair bill

$1,200 Veilside kit....}

$2,500 full re-spray..} in progress

and theres more to come in the future... :D

  • Replies 68
  • Created
  • Last Reply

Top Posters In This Topic

PFC: 750

Tuning: 450

Bodykit: 800 on top of selling my old kit

Cat and forward sections of exhaust: 1000

Front mount: 1100

Stereo: 1300

Alarm: 850

Rims: 1200 on top of selling the rims my car came with

Strut brace: 130

Gauges & rsm: 800

Tinting: 200

Cam gear: 130

Suspension: 550

Upgraded fuel pump Bosch 040: 230

GFB Hybrid BOV : 150

Cold air box: 120

TOTAL: 9760... OOoppss.. LOL... Still more to come :) This is just on modifications. This doesnt include petrol expenses, oil changes etc...

This thread was created just to rub it in for the GTR guys right? :)

GTR thread: 20k, 15k, 7k, 12k,

GTS-t thread: 2k, 2k, 2k  

LOL

lol nah i was just curious to see if alot of gtst owners and such spend alota money on there car as well, although it would suck being a GTR owner and reading this lol.

haha i like the way alot of you say a figure and then add ( so far ) to the end of it lol, i should proly bring it up again in a year or two and then maybe we'd be up to the GTR figures ;).

Wheels - $2500

Susp - $3500

BC - $300

POD - $100

Zorst - $1200

Stereo - $7000

Brakes - $700

Fansy stuff - $1000

Purchase price - $19000

Total - $35300...........DAMN! and i still have sh!t loads to go.. ;) cars are expensive.

Car - $21K

First Batch of mods - $13K (FMIC, Hi Flow turbo, Injectors, ECU, Tune, Front/Dump, cat, etc)

Blown Motor

Second Batch of Mods - Engine Rebuild $20K (included new everything - bulletproof)

New Turbo & manifold - $3K

New ECU $1400

Greddy Plennum - $1.2K

Buddy Club Wheels - $2K

TIEN Suspension - $1.2K

Clutch - $650

New Springs - $450

Oil Cooler, Thermostat, lines - $1K

Bigger FMIC - $1600

Sound System $1K

Semi Slicks - $1100

Terrific waste of money ;)

Purchased mine 5 years ago and it owes me close to 50k including purchase price and labour for installed parts

Same here :P and i am still getting more mods in the next few weeks. Long engine is still std., for now :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...