Jump to content
SAU Community

Recommended Posts

Hi, I've just bought a Greddy V-Spl cooler (yet to fit it), and was just wondering a few things...

1. Is a pod filter needed (i.e. cannot use the stock airbox) for one of these on a 32 Gts-t?

2. Do u need to cut a hole in the arch (wheel) to accomodate the piping?

3. Is it a simple bolt on, or is a bit of stuffing around need to bolt these things up.?

4. Is a different Battery needed for this cooler (to make way for the piping)?

5. How do these things go as far as radiator flow?

6. How do these rate against the stock cooler?

7. What boost is anyone running with one of these on an RB20DET?

Any help would be appreciated...

Cheers David

Link to comment
https://www.sau.com.au/forums/topic/81363-r32-greddy-vspl-intercooler/
Share on other sites

Hi, I've just bought a Greddy V-Spl cooler (yet to fit it), and was just wondering a few things...

1. Is a pod filter needed (i.e. cannot use the stock airbox) for one of these on a 32 Gts-t?

2. Do u need to cut a hole in the arch (wheel) to accomodate the piping?

3. Is it a simple bolt on, or is a bit of stuffing around need to bolt these things up.?  

4. Is a different Battery needed for this cooler (to make way for the piping)?

5. How do these things go as far as radiator flow?

6. How do these rate against the stock cooler?  

7. What boost is anyone running with one of these on an RB20DET?

Any help would be appreciated...

Cheers David

1. No standard airbox is fine.

2. Hole in the wheel arch???

3. It's a straight bolt on and only very minor modifications are needed to fit it.

4. All depends on the size of your current battery as they come from Jap land with heaps of different styles and sizes.

5. Your radiator will still get ample air flow.

6. Flow much better than the standard cooler.

7. If the only mod you have/will have is a cooler and say exhaust, about 12 psi would be ample. If you would like to run more boost, it is recommended that you upgrade your fuel system and either remap your standard ECU or get some form of aftermarket ECU.

make sure u have all of the support mods like said above..

get exhaust- prefferably turbo back, i.e dump pipe, front pipe and cat back..

get a panel or pod filter... a fuel pump is not needed if ur running abt 12 psi..

however, a tune is defenite... Get a piggy back ecu if u can afford it like an SAFC or emanage, or even get ur stock ECU remapped...

its all in the tune.. it does not mean the more psi u run, the more power u will achieve..

hope that helps..

Rob

Hi, Does anyone know if the R34 VSPL Intercooler kit its going to interfere with the standard snorkel and after looking at the pics of what comes in the kit, do I need any additional piping made up or does it just use the existing piping?

Thanks heaps. Pics if possible of what comes in the kit would be good (if it isnt what is shown on www.nengun.com). I have a cold airbox that uses the factory snorkel at the moment and wouldnt want make it a waste when i get the cooler.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
    • Just like in being 14mm too small (296mm) makes it not fit, being 14mm too big (324mm) it also won't fit. You want to find the correct rotor.
    • @GTSBoy Ok so that was the shops problem...they showed R33 rotors on R34 page and i did not know 296 do not fit(and are for R33) Yes i bought "kit" with rotors and pads. Pads are ok(i have GTT calipers front and rear). They have some 324mm but no 310mm. So i dont know if they would fit. I have 17inch LMGT4s So another question. Can i fit those in the rear or they are just "too" big for that?
    • I started removing the tank a while back with the intent to give it a proper clean. Got to a bolt that I couldn't undo completely due to a diff being in the way, so just said f**k it and siphoned the gluggy old fuel out and called it a day. Looking it the tank it looks less corroded than the one in the pics for that billet hanger from Frenchy's anyway. Isn't it the fuel filters job to worry about this stuff? I scraped off most the crusty shit of the hanger but will give it another go before reinstall coz maybe the fuel and return pipes are also full of gunk  
    • Pretty sure it is a common fault. I believe this is the only part you need, but don't quote me as I don't have a V36.  I also believe it is a bit of a pain to change and the device needs to be encoded to the car once it is replaced, so may need someone with the right tools. Buy Genuine Nissan 48700JF00D (48700-JF00D) Lock Set-Steering. Prices, fast shipping, photos, weight - Amayama
×
×
  • Create New...