Jump to content
SAU Community

Recommended Posts

Looking for new turbo, garrett reccommended 3040R with .63 housing.

They said would not be laggy and being 600hp would make more then enough power.

any thoughts and experience with this turbo? especially on rb20?

it is ext gated! Due to it not being a straight bolt on is it going to cost heaps to have put on with new wastegate etc etc.

Is that kind of set up "Cop bait"?

thanks

Link to comment
https://www.sau.com.au/forums/topic/81393-garrett-3040r-on-rb20/
Share on other sites

Anyone know??

Looking for new turbo, garrett reccommended 3040R with .63 housing.

They said would not be laggy and being 600hp would make more then enough power.

any thoughts and experience with this turbo?  especially on rb20?  

it is ext gated!  Due to it not being a straight bolt on is it going to cost heaps to have put on with new wastegate etc etc.

Is that kind of set up "Cop bait"?

thanks

I run one on my ca18 with all the necessary hardware and i really think its more like 510-520hp. we made 415whp @27psi on bp ultimate ezy tune dont think there would be much more in it and its a little laggy although would be good on a 6cyl 2.0ltr.

I personally think the .64 housing wont be that bad on an RB20. If you get a good port job done and an aggressive camshaft set up I think this will come on boost nice and early.

Ok in regards to your question about if the turbo is internally or externally gated. I think they come in both but dont quote me on it.

Cop bait! OH YEA!!! Especially if you are living in Melbourne.

Hope this info helps

Looking for new turbo, garrett reccommended 3040R with .63 housing.

They said would not be laggy and being 600hp would make more then enough power.

any thoughts and experience with this turbo?  especially on rb20?  

it is ext gated!  Due to it not being a straight bolt on is it going to cost heaps to have put on with new wastegate etc etc.

Is that kind of set up "Cop bait"?

thanks

dude,

what are u after out of your car?

the gt3040r (with A/R .63) is quite a big turbo and wouldn't be all that responsive for a street driven RB20DET.

it all comes down to how much power you are looking for out of your car and how/when you want to make that power.

i personally had one of these on my car (sierra cosworth), and although it made pretty good power (~280rwkw @ 24psi), it didn't provide the response i actually wanted. this was due to the big compressor wheel it has.

so as above, work out exactly what u want out of the car and then we'll try to help you.

Dude, drop me a PM, i'll try to help you out.

good luck.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
    • This looks great! Awesome to have the 5 speed with an LSD in this. The Recaro's look like SR2's or SR3's. It's a shame they've been retrimmed as they would have looked sweet in their original colours. I think I'd want my agent to be a little more up front and informative too. I've never imported but I reckon it would make me a little nervous, so the more info the better.
×
×
  • Create New...