Jump to content
SAU Community

Recommended Posts

Hello

I know that there is some killer thread out there with all of this info on o2 sensors... but the point of this question is if there is a specific part for the 34 GTT or does the Ford EL work on that too? Most of the guys there were talking about 33 or 32 sensors and not the 34.

I'm gettting about 350kms out of a full tank with no pretty much stock gear (panel filter from k&n + boost at 10psi) - car has 40k kms clicked on it, should I be looking to get a new o2 sensor?

Any help or direction to specific parts would be most appreciated~

Link to comment
https://www.sau.com.au/forums/topic/81460-r34-gtt-o2-sensor-replacement/
Share on other sites

I'm going to get my exhaust fitted today; will ask about the fuel economy and whether or not it'll be a good idea to change the o2 sensor...

Hopefully will get a part number or two out of the conversation.

Hey tdawg,

I asked my mechanics today and they said that the o2 sensor should not be playing up - they even said the 350kms is quite normal for the car... I seem to think otherwise.

I've had some soot build up since installing the cat back so I might just invest in a new o2 sensor (at least if the new one doesn't make a diff, I'll have a spare one to use).

Thanks

Best way to check it would be to put an voltmeter on it and look at the feed back you get from it.

If they are replacing them with ford EL ones, I would near say that you could get the specs out of the ford service manual or a Gregory's EFI manual.

I would think that it would take a reference voltage and modify it. I doubt it would be a signal generating one. But, if it is a signal generator you would have to get a oscilloscope. At a edumacated guess, at 3 wires it should be a potentiometer you will have an input 5-12V, an Earth, and an output which should vary - thats the one you want to monitor.

Cheers

Sumo

Is that your "city cycle" economy. If so, it's unlikely a new O2 sensor will help, because, as has been mentioned too many times on these forums, the O2 sensor really only works under constant throttle (cruise) conditions. Around town, you get very little time on cruise (compared to "highway cycle").

Your O2 sensor operates up to 4000rpm and just below 0 vacumm. Hold the revs above 2500 rpm and check the voltage between ground and the signal voltage you can do this at the sensor or the ECU it dosn't matter as long as there is continunity. What you should see is an oscillating voltage between 0-3 volts I think. I'm pretty sure if you can replace the O2 sensor with an EL sensor the voltage variation will be between 0-3 volts. I know most 02 sensors are 1 volt but I think there where a few fords with 0-3 volt O2 sensors, perhaps someone could elaborate.

So the Ford sensor will work on the R34?

Ever since getting the Cat Back installed, I've begun developing quite a bit of soot on the rear bar after every drive. In the other threads, some have said that the new o2 sensor has cleared this out completely...

Someone care to make a suggestion or two? I definitely know that the car is running rich now that the soot is developing. Carbon just ain't burning completely...

So the Ford sensor will work on the R34?

Ever since getting the Cat Back installed, I've begun developing quite a bit of soot on the rear bar after every drive.  In the other threads, some have said that the new o2 sensor has cleared this out completely...  

Someone care to make a suggestion or two?  I definitely know that the car is running rich now that the soot is developing.  Carbon just ain't burning completely...

Mate,

I get the same problem aswell, so much build up around the boot and bootlid, but my exhaust is from the turbo back. Again it must be a common problem with the r34's must be unburnt fuel.

Well regardless of what's the go on the 34 (dead or un-dead), my car just clicked 40k Kms so I'm going to replace the o2 sensor just to be sure. On the other thread it was stated the following effects:

1) Increased Economy

2) No more black soot on rear bar

3) Better performance (not power, just overall engine running)

disturb3d - I'm going to get a 3" front/dump pipe as well as a 3" high flow cat installed soon... I don't want to have black bumpers after each drive - will let you know if the o2 sensor changes anything!

An O2 sensor will not change the soot being produced at full throttle.

The O2 sensor is only used when the ECU goes into closed loop mode - which is at idle/cruising. The ECU at full throttle looks at the AFM signal and tries it best to make decisions based on that reading. It doesn't try and lean it out till things are nice cruisey, less risk of leaning a motor out and causing damage.

Cheers

Matt

Try cleaning the injectors - they may have a bit of gum build-up, permitting too much fuel to be injected.

Try going for a "cruise" along the highway - the Central Coast must be nice this time of year.

Mate, Im not too sure what would produce better fuel economy. If everything is checking out fine I would look at your driving styles, the right foot controls most of your economy.

Blocked injectors I would think you would have worse trouble then bad economy - but it is plausable.

Small things produce better economy as in good quality engine oil, clean air filters, pumped up tires, quality fuel, IAC working properly (your car adjusts idle as it warms up?).

Im not to sure on what kind of memory capability the skyline has, but maybe its worth erasing that by undoing the battery and pushing the brake pedal. Should reset a few values the car "learns" about different throttle and load positions.

Cheers

Sumo

Thanks for all your help Sumo...

Looks like i'll be replacing the o2 sensor, running a bottle of injector cleaner through the car, as well as resetting the ECU (properly this time).

Will post up any improvements at a later time! :D

Is always good to hear on what kind of results people get by trying different things.

I have never really taken notice how many kms I get to my tank in the 33. I always forget to check the trip meter or reset it.. By all means if you can replace the O2 sensor and run an injector cleaner (I used Caltex Techron 5000 to get rid of my nasty injector noise my car got from 5hit fuels we get out here in the country) , If it produces no result, back to the drawing board - but if it does your set :D

Cheers

Matt

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I do believe from context he is talking about a S0/S1 R33 RB25 with associated ECU and Wiring for that, and a manual gearbox into a R34 N/A Auto. I don't have the knowledge of all the pinouts and such but my gut feeling from doing my own conversion is to use as much of the R33 stuff that you can. The "car" wiring is quite seperate from the "Engine" wiring when all things are considered. The only things to truly consider 99% of the time is the cluster, reverse lights and potentially disabling the 'not in P/N' immobilizer circuit.
    • A realistic expectattion of how long it has to last also comes down to.... when do you think you will be banned from registering and driving old petrol powered shitters? It's 27 years since that thing was built. It probably rusted out 15 years ago. It was probably repaired and looked OK for another 10. If you do a similarish bodge job now, or perhaps slightly better with some actual rust conversion and glassing, then.... get another 10-15 years out of it, after which you'll only be permitted by the CCP to drive electric cars manufactured in their Shenzen zone anyway. 
    • Let me assume that the concern over a manual ECU is that the NeoDET that you have was an auto and has an auto ECU. That ECU will not be a problem, but you WILL have to Nistune it. And you would have to Nistune it even if you had a manual ECU, because the turbo ECUs will shit the bed if they do not have all the things that they were told they have to have, to be happy. The big one being the TCS CU, which you won't have in your car. Anyway, with an auto ECU (which I have running my originally auto NeoDET in an R32) Nistune allows you to put in a Stagea image which doesn't panic about the absent TCS, and allows you to override a whle bunch of other annoyances that would otherwise see the check engine light on 100% of the time. Also, you can't wind up the power very far on the stock NeoDET ECUs without Nistune, because the boost sensor gets in the way. Nistune allows you to push that problem much further up the dial. Do you even have the boost sensor with the engine? Without it, you are SOL and will need an aftermarket ECU (or to find a sensor somewhere, god knows where). I can't tell you what the wiring loom differences are in a 34. But what Duncan said above needs to be considered. When you say "loom", does that include the transmission loom? Because you will need to swap out the auto tranny loom for the equivalent manual loom, and get rid of the neutral/park start interlock (basically hot wire it).
    • I have had the r3c in for years now, maybe close to 7 years and it has never missed a beat, anyone can drive it. Super easy to drive around town, the hotter it gets does get a little hard but it holds the power easy as 
    • Shit thing to find eh? I guess the big issue is that whatever "fix" you do now, it might slow the rust down but won't fix it. I just wanted to add that in no way is fixing sheet metal in 3 dimensions the place to start with welding....that is a pro only job because its too hard to work out where things should be, let alone doing a clean enough job that it can look OK and still be strong too.  I needed to get a new rear quarter panel on the GTR and it took a pro weeks to get the old one off cleanly, new one on in the right place and looking somewhat like it should have with most of the previous connecting panels in place. Gluing a couple of bits of metal together with a welder in the garage is doable, but that is totally different to doing panel  replacement
×
×
  • Create New...